20 Most Recent 2005 Mazda 6 Questions & Answers

0helpful
2answers

No crank no start Mazda 6 2005

Hello. It seems there is a problem with either your car's starter relay, wiring and/or ECM. Most 'functions' of modern vehicles goes through the ECM. Good luck and keep me informed; if you want to.
9/6/2021 4:47:56 PM • 2005 Mazda 6 • Answered on Sep 06, 2021
0helpful
1answer

Can I use a battery stronger than recommended for a Mazda 6 2005?

Yes, as long as you are talking about amps and not volts.
8/21/2019 5:23:18 PM • 2005 Mazda 6 • Answered on Aug 21, 2019
0helpful
1answer

2005 Mazda 6 - It turns over for a second - then the alarm goes off stopping it from starting - It wont start do to the alarm stopping it. Battery seems to be charged enough. What could be happening.

Hi there's this website something like reliable-store and it is very amazing for manual for repairing servicing anything someone on fixya recommended it to me and I thank him even today
2/1/2019 10:24:18 AM • 2005 Mazda 6 • Answered on Feb 01, 2019
0helpful
1answer

Gadatargmna

removed
1/9/2019 10:08:00 AM • 2005 Mazda 6 • Answered on Jan 09, 2019
0helpful
1answer

Mazda 6 starting problem

You will get your solution and all info on service info, repair info, parts info, wiring/electrical/fuse diagrams, error/fault codes, torque specs, PCV, owner's/service/repair/parts/maintenance manuals etc everything this website www.reliable-store.com it's a very good website for vehicle problems even as old as 1991 ford..
3/19/2018 5:08:37 PM • 2005 Mazda 6 • Answered on Mar 19, 2018
0answers
0helpful
1answer

What is causing my 2005 Mazda 6 sport wagon to run jerky and not accelerate smoothly.

If it started only 3 days ago, go to your auto parts store and the next time you fill up, add a can of Sea Foam. If there is a gas station near you which sells gasahol-free gas, fill it up with that, then take it out on the interstate and kick it into passing gear several times (I hope you don't get a speeding ticket).
11/9/2017 1:33:18 AM • 2005 Mazda 6 • Answered on Nov 09, 2017
0helpful
1answer

2005 Mazda 6 4cyl AT Idles high after driving a while.

I would check the pedal position sensor. Do it when it's hot. Mazda Car 2005-06
  • Accelerator Pedal Position Sensor

    Description & Operation A power supply is applied on the Accelerator Pedal Position (APP) Sensor (main) power terminal from the PCM. The ground terminal is grounded with PCM. When the accelerator pedal is moved from the idle position to the fully opened position, the resistance between the accelerator pedal position sensor (main) output terminal and ground terminal will increase according to the depression. A power supply is applied on the Accelerator Pedal Position (APP) Sensor (main) power terminal from the PCM. The ground terminal is grounded with PCM. When the accelerator pedal is moved from the idle position to the fully opened position, the resistance between the accelerator pedal position sensor (main) output terminal and ground terminal will increase according to the depression.

Testing
  1. Connect a suitable scan tool to the diagnostic connector. Select APP1 or APP2 percentage.
  2. Turn the ignition switch to the ON position.
  3. Measure the voltage at the PCM terminal and ground with connectors connected: APP1-8% load or 0.4 volts with the accelerator pedal releasedAPP1-60% load or 3.0 volts with the accelerator pedal depressedAPP2 -8% load or 0.4 volts with the accelerator pedal releasedAPP2 -60% load or 3.0 volts with the accelerator pedal depressed
  4. If any check above does not meet the specifications, check connectors and wiring between the sensor and PCM. If ok, replace PCM.
  5. If the measured values are outside the standard value range, or if the load % and/or voltage does not change smoothly, replace the sensor.
  1. Connect a suitable scan tool to the diagnostic connector. Select APP1 or APP2 percentage.
  2. Turn the ignition switch to the ON position.
  3. Measure the voltage at the PCM terminal and ground with connectors connected: APP1 %-31.0-32.4% with the accelerator pedal releasedAPP1 %-69.8-81.8% with the accelerator pedal depressedAPP2 %-20.2-21.4% with the accelerator pedal releasedAPP2 %-58.8-70.8% with the accelerator pedal depressed
  4. If any check above does not meet the specifications, check connectors and wiring between the sensor and PCM. If ok, replace PCM.
  5. If the measured values are outside the standard value range, or if the load % does not change smoothly, replace the senso
0996b43f80203317-l15fcbeisfileg1jtnhunp3x-3-0.gif
7/24/2017 12:08:22 AM • 2005 Mazda 6 • Answered on Jul 24, 2017
0helpful
1answer

05 mAZDA 6 - ENGINE BEGAN SURGING THEN IT WOULD STALL USUALLY ABOUT 1500 RPMS. mazda dealership said sounded like computer so we brought one and it didn't fix it. It stayed in the shop for 6 weeks

first -for it to record a fault the car has to be run for some time --15 minutes or 50 miles because intermittent faults are not always recorded as an example consider this on your phone you have a pin number now if you press the incorrect numbers 2 times nothing happens and you can start again next day ( in the car it is like you pressing the numbers 2 times = no code) however press the incorrect number 3 or more times , you need a PUK code to get back in ( in the car pressing the wrong number too many times = to a code now being reported) carefully record when it stalls ( at lights with the foot on the brake), changing down ratios when slowing down) surging on acceleration--rpm reading is critical or deceleration --road speed and engine rpm correlation fuel level situation when it occurs ( full , partially full or close to empty) from you statement, I would suggest that you put a can of quality injector cleaner in the tank on filling for a couple of fills as it indicates an injector/s problem and that will not record a code unless a cylinder misfires for a set period of time it is easier to do the simple things first then have the codes read by an accredited service shop that has experience on your make of car
7/8/2017 2:44:11 AM • 2005 Mazda 6 • Answered on Jul 08, 2017
0helpful
2answers

What could be causing my 2005 mazda 6 to keep dying while I am driving it?

Have the codes read with a scan tool. Most auto parts stores will do it free.
7/1/2017 12:41:06 PM • 2005 Mazda 6 • Answered on Jul 01, 2017
0helpful
1answer

Why won't the fuel pump shut off

Fuel pump won't be the cause. Most likely the relay.
4/6/2017 12:48:20 AM • 2005 Mazda 6 • Answered on Apr 06, 2017
Not finding what you are looking for?
2005 Mazda 6 Logo

564 questions posted

Ask a Question

Usually answered in minutes!

Popular Products

2004 Mazda 6
2004 Mazda 6

739 Questions

2003 Mazda Mazda6
2003 Mazda Mazda6

453 Questions

2006 Mazda 6
2006 Mazda 6

291 Questions

2007 Mazda MAZDA6
2007 Mazda MAZDA6

74 Questions

2008 Mazda MAZDA6
2008 Mazda MAZDA6

48 Questions

Top Mazda Experts

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6928 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14942 Answers

Greg Bernett
Greg Bernett

Level 3 Expert

2993 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

MAZDA6 Mazda

  • MAZDA6 Mazda

Most Popular Question

motor mazda 6 2005 4 cyl seems seized

  • Cars & Trucks
Loading...