2002 Chevrolet Tracker - Answered Questions & Fixed issues

Should be on the right rear valve cover depending on the exact engine size if its a 4.3 or 3800 ect. hope this helps.

you wil probably need to replace the entire switch assembly which will include other windows switches aswell. but the assembly will be reasonably easy to remove from the door and swap out (you may or may not need to remove part or all of the door trim to do so). just remember to put the wires back exactly where they came from on the new unit.

Let's get this if we have this right ! When you turn the key to the start position ,the starter engages an spin's the engine around , But does not Start ? If that is the case ,why on god's green earth did you take the starter off an have it checked ? An if it doesn't spin the engine over ,how do you know it doesn't have spark ? From your posting it clearly sounds like you don't have any diagnostic skill's , so do youself a favor an have a professional shop check it out .

This place is a good place to start. http://www.bbbind.com/free_tsb.html Hope this helps

could be a bad solenoid in the trans.

I think I would start by changing the broken TPS with a new one.

Drive as is will cost a lot to fix this problem, keep eye on it.

Injector maybe ! What's that cylinders comprssion ?

Try adjusting the neutral safety switch on the side of the transmission.

My info says 73.8 ft lbs. 2wd

Note the diagram. Maybe problem with shift solenoid?

Cylinder Misfire Detected Random Cylinders http://www.autocodes.com/p0300_chevrolet.html

Get a Chilton manual from any auto parts store to get a step by step instruction with diagrams.

1. Disconnect the negative battery cable.
2. Remove the air cleaner hose.
3. Disconnect the starter solenoid electrical connector.
4. Remove the retaining nut and positive battery cable (3) from the starter solenoid.
5. The starter motor on manual transmission equipped vehicles are secured with 2 bolts. The starter motor on automatic transmission equipped vehicles are secured with a lower bolt and an upper nut and bolt. Remove the upper mounting bolt (1) and the negative battery cable from the starter motor assembly.
6. Remove the lower mounting bolt (1) and the starter motor assembly from the vehicle.
7. Install the starter motor assembly to the vehicle.
8. Install the lower mounting bolt. Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.
9. Install the upper mounting bolt and the negative battery cable. Tighten Tighten the starter motor assembly mounting bolts (1) to 30 N·m (22 lb ft).
10. Connect the positive battery cable (3) to the starter solenoid. Secure with one nut. Tighten Tighten the starter solenoid nut to 10 N·m (89 lb in).
11. Connect the starter solenoid electrical connector.
12. Install the air cleaner hose.
13. Connect the negative battery cable. Tighten Tighten the negative battery cable-to-negative battery terminal retainer to 15 N·m (11 lb ft).

The light switch can over ride the DRL. If it doesn't. You have 3 possibilities. The switch s bad, the light sensor is bad, or the BCM is bad or not receiving signals. Have the codes read for the BCM.. Takes a scanner. Not a code reader.

Voltage drop test starting system , could be a bad cable . Starter Voltage Drop

install star wheel toward the self adjuster arm

Passenger side of engine compartment. Just below the air duct after the mass air flow sensor. Straight down below throttle positioning sensor. Sorry don't have diagram. Hope this helps.

You have to remove the instrument cluster from the vehicle and the bulbs are replaces from the backside.