fuse box diagram for a 1998 pontiac bonneville se 3.8L
I am replacing a rear brake line, from the pump back, and there is a silver cylinder that the line goes into and comes out on located near the fuel tank. There is one on bothe lines....what is it?
It is a brake proportioning valve. Dealer only part.
Posted on Sep 17, 2008
I have a 1998 pontiac bonneville SSEi, the fuse box panel, on the drivers side, has been misplaced and I need to figure out which fuse goes to the heater. any suggestions on how to get the fuse box dagram?
Posted by hugmebear2 on
I have taken a picture of the fuse panel diagram and can send it to anyone if given an email address. Photo is to large to upload here and I don't know how to shrink it!
Posted on Jan 04, 2011
leaky transmission fluid. possible reasons?
Posted by jerjohn58 on
TRANSMISSION LEAKS COME FROM TRANSMISSION OIL PAN GASKET LEAKING.OIL COOLERS LINES LEAKING.LEAKING AT TORQUE CONVERTER FRONT SEAL.TRANSMISSION SPEED SENSOR SEAL LEAKING.FRONT AXLE SEALS LEAKING AND LEAKING AT TRANSMISSION COOLING LINES TO RADIATOR.CHECK ALL YOU WILL FIND LEAK.IF YOU HAVE FAST LEAK OR PRESSURE LEAK.WITH CAR RUNNING IN PARK EMERGENCY BRAKE APPLIED LOOK UNDER CAR IF YOU SEE FLUID LEAKING OUT IN LARGE QUANITIES.COOLER LINES LEAKING OR TORQUE CONVERTER FRONT SEAL LEAKING.IF YOU HAVE SLOW LEAK THE LEAKS HAS TO BE AXLES SEALS OR PAN GASKET LEAKING OR VSS SENSOR SEAL LEAKING.
Posted on Aug 07, 2010
Need a belt diagram for a 1998 Pontiac Bonneville SSEI
Posted by caustin_5 on
This should Help
Posted on Mar 02, 2011
I had an emission test done on my 98 bonneville and it failed because code P0440 evap control system what should i do ?
Posted by king5197 on
Here's list why your car is coming up with this code. It could be any of these things causing it.
DTC detecting condition:
Posted on Apr 01, 2010
where are all the relays located in a 98
Posted by tori tori on
I think it's above the cowl in the engine compartment. Download the 99 owners manual and turn to page 6-62
Posted on Mar 08, 2012
I have a 1995 pontiac bonneville and I need the instructions to program a factory remote.
Posted by galante007 on
95 bonny--1-turn ign switch off
2-using a fused jumper wire jumper data link connector #8 blk/wht wire to #4 blk wire (look under dash for dlc)
3-press unlock button on 1 transmitter doors should lock and unlock
4-repeat step 3 if doing more than 1 remote
5-remove fused jumper
for the 1993 car same way except jumper term a blk/wht
term g ppl/wht
Posted on Feb 08, 2009
looking for torque specs and sequence of both intake manifold and plastic plenum on 98 pontiac bonneville 3.8 non turbo
Posted by chrisforma... on
Lower intake bolts 11 ft. lbs start in the center of the intake and work your way out cross from side to side.Tighten the upper intake bolts with the same procedure with 89 inch pds.Be sure to apply threadlocker to the lower intake bolt threads.
Posted on Feb 07, 2010
need a diagram of the serpentine belt for a 1998 pontiac bonneville v-6 no turbo
Posted by scmeester on
it is on a sticker adhered to your radiator shroud.
if it is removed, damaged, or unclear...
one tip - if you look by the crankshaft pulley to the right you will see a tubular looking shaft about 1" diameter , you will notice you can't get the belt out from under this piece , it has a nut on it , once you take the nut off , you will notice it has a star shaped point on the tip of the stud , it requires a reverse torx socket or wrench to remove the stud , when you get the stud out the tube piece it can be removed , then the belt comes off , replace the belt , now comes the tricky part , fitting that tube spacer back into its spot , it can be difficult , once its in place put the stud back in , and put the nut on and tighten it.
Thanks for using FixYa - a FixYa rating is appreciated for taking the time to answer your FREE question.
Posted on Mar 19, 2009
762 questions posted
Usually answered in minutes!