20 Most Recent
- Page 6 Questions & Answers
Must add power steering fluid every two days.
Yes you can replace the steering rack rubber boots OK.
But if you are loosing fluid, it sounds like the internal seals are leaking, allowing the fluid to fill up these boots, and subsequently bursting them, so you will be back to square one.
Better to fit an exchange steering rack !
Good luck !
A FixYa rating would be Nice !......... Thanks.....John.
At operating temp 171 - 181 F, with SAE 10w-30: idle @ 700 rpm 11 psi min, 1200 rpm 28 psi, 2000 rpm 43 psi, and 4000 rpm 57 psi.
I need to put a
In stores (autozone) you can pick up a Haynes repair manual for about $20 it has step by step instructions including pictures and diagrams.
I don't have a problem
Kelley Blue Book
an '89 SE (furthest they go back) Auto Trans, etc. has a "fair" condition value at $890 - Excellent $1490
Offer him $1000 and he'll prolly take it!!
Thanks for using FixYa - a FixYa rating is appreciated!!
Remove anit-theft system
If you use the drivers outside door lock to unlock the vehicle it should disarm the vehicle. emmissionwiz is correct, you can't simply shut the factory alarm off.
water pump replacement is an easy job I would do the
timing belt while I had the front taken a part. That would mean you
need the belt and tensioner.taking the radiator out is the best
way unless you want to remove the inspection plate to get access where
you can lock the ring gear to keep the engine from rotating when you
take the harmonic balancer bolt off. I would purchase a gasket and
begin the process. The cost to have this job done is quite expensive.
But, if you have never done one of these it might be left to a Nissan
shop. That is, unless you know someone that can walk you through the
Engine light is on so
CODE P1574 - ASCD VECHICLE SPEED SENSOR. POSSIBLE CAUSES, HARNESS OR CONNECTORS CAN COMMUNICATION LINE IS OPEN OR SHORTED. UNIFIED METER AND AC AMP. VDC TCS ABS CONTROL UNIT WITH VDC MODELS. ABS ACTUATOR AND ELECTRIC UNIT CONTROL UNIT WITHOUT VDC MODELS. FAULTY WHEEL SENSOR. TCM AT MODELS. ECM FAILED.
Where is the cruise control fuse located on a Maxima 2000 GLE
Refer to Owner's Manual for ASCD operating instructions. POWER SUPPLY AND GROUND NFEL0190S01 When ignition switch is in the ON or START position, power is supplied: + through 10A fuse [No. 30, located in the fuse block (J/B)]
to ASCD brake switch terminal 1 (LHD models) and + to combination meter terminals 47 and 50. + through 15A fuse [No. 20, located in the fuse block (J/B)] + to park/neutral position relay terminal 1 (A/T models), + through 10A fuse [No. 10, located in the fuse block (J/B)] + to ASCD control unit terminal 5, and + to ASCD brake switch terminal 1 (RHD models) Power is supplied at all times: + through 15A fuse [No. 2, located in the fuse block (J/B)] + to the stop lamp switch terminal 1, and + through 10A fuse [No. 57, located in the fuse block (J/B)] + to the horn relay terminal 2. When park/neutral position is in the P or N position (A/T models), ground is supplied: + to park/neutral position relay terminal 2 + through park/neutral position switch and body grounds F41 and F39. When ASCD main switch is depressed (ON), ground is supplied: + to ASCD control unit terminal 9 + from ASCD steering switch terminal 4 + to ASCD steering switch terminal 5 + through body grounds M9, M25 and M87 then ASCD control unit holds CRUISE condition.
Not finding what you are looking for?