20 Most Recent 1992 Chevrolet S-10 Questions & Answers


Visit the on-line store, know as reliable-store, they have the repair manuals. I'm sure you will get the solution of your problem.
Best Manuals

1992 Chevrolet... | Answered on Dec 30, 2019


The fuel pump circuit was a common cause for this . Any place between the pump and fuse can have a bare spot in the insulation intermittently bumping into metal . I believe the injectors may run on the same circuit so check their wiring also .

1992 Chevrolet... | Answered on Nov 10, 2019


yes -recheck all work done and test all components for power and correct operation

1992 Chevrolet... | Answered on Jul 11, 2019


locate the tan wire with black stripe under the dash on the passenger side it should be taped to the harness unplug the inline connector and esc will be disabled for setting the timing

1992 Chevrolet... | Answered on Jan 14, 2018


Look carefully and you should be able to tell.If you can see that the pan can slide out of the way, you should be good to go.

1992 Chevrolet... | Answered on Jan 11, 2018


Do you mean the small handle tips on the levers are preventing you from removing the plate? Normally, those tips should just pull off, then the plate can slide off over the levers.

1992 Chevrolet... | Answered on Jan 09, 2018


should be in the glove box, or under the driver side dash. May need to remove under dash cover.

1992 Chevrolet... | Answered on Dec 31, 2017


https://s1.postimg.org/89tia75ozz/turn_signal.jpg

Click on the link.
This is for turn signals. Get at the turn signal switch. See the purple wire, L terminal on top of turn signal switch in diagram, that should go hot with key on, use jumper wire from that terminal to one of the wires on bottom of turn signal switch in diagram, those are, front/rear, left/right turn signals. If the turns signals work properly with the jumper, but, other wise don't, the problem should be the turn signal switch. If it still doesn't work properly, you would have to check wiring circuits.
Sometimes a faulty ground can cause weird problems. Sometimes the bulb doesn't make good contact in the bulb socket? Try putting a little pressure on the bulb in the bulb socket, see if it starts working?

1992 Chevrolet... | Answered on Aug 01, 2017


Make sure the battery has a full charge. What is liter size of engine? If you have throttle body injection/tbi can you see fuel injector pulse, both fuel injectors, if you have two. The fuel pressure for tbi is around 9--13 psi, it wouldn't hurt to use a gage and check fuel pressure.
Engine cranking, you have spark at the plugs and fuel injector pulse? How long since a tune-up? Any applicable trouble codes? Your obd1, you should be able to check some codes, yourself, if the check engine lite still works.

1992 Chevrolet... | Answered on Jul 30, 2017


Have a look at the fuel pressure regulator.

1992 Chevrolet... | Answered on Jul 11, 2017


Sorry but I would need to see what is going on to help you with this.

1992 Chevrolet... | Answered on Jul 05, 2017


Near the thermostat housing or in the housing cover on the intake manifold.

1992 Chevrolet... | Answered on Mar 20, 2017

Not finding what you are looking for?

582 questions posted

Ask a Question

Usually answered in minutes!

Popular Products

Top Chevrolet Experts

Marvin
Marvin

Level 3 Expert

85239 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8984 Answers

john h

Level 3 Expert

23504 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

S 10 Chevrolet

  • S 10 Chevrolet

Most Popular Question

92 s10 5 speed 2 8 starts up fine cold

  • Cars & Trucks
Loading...