20 Most Recent
Questions & Answers
Where is the bcm fuse on a 2005 Chevy Colorado?
dont need to remove bcm fuse to program a fob the bcm needs to be active to program standard for - unless you have remote start then needs to be flashed to your vin by dealer or an authorized shop this link is for the lock unlock standard fob https://itstillruns.com/program-colorado-key-fob-7191242.html
I need a schematic of the ignition switch
I have an 05 Chevy Colorado and it won't start , I replaced the fuel filter the air filter and even replaced the fuel pump , then I put on a diagnostics check and it said there is no error code , the truck turns over but still will start it seems to be a fuel problem to me.
2005 Chevy colorado remove camshaft sensor
you can get guide from many sites.. i know few
error codes/ fault codes, wiring diagrams, schematic diagrams, torque specs, engine info, switches functioning, assemble, disassembly, complete refurbish, repair, installation every single thing is covered
within seconds u can get the access and it's totally illustrative complete
Reduced power code comes up and my truck stalls.
I had the same problem, and the solution was cleaning the throttle body, it does need to be completely removed to be cleaned thoroughly. I just used some brake cleaner on a rag to clean off all the carbon deposits. A friend of mine who is a dealer tech had only seen this trouble code once, and this was the solution. So far, my light has not come back on and the truck is running alot better at idle.
2005 chevy colorado wipers won't work.
This diagram is part of wiper circuit. Couldn't get everything in one picture. There could be other issues?
bbbind.com should have wiring diagrams for your wipers. You can look at the whole thing.
The engine in your car is designed to run smoothly with maximum power
output and produce as minimal emissions as possible. When your car's
engine is not performing properly it can cause, low gas mileage, low
power output, increased emissions and possible internal engine damage
if left untreated. This troubleshooting guide is designed to isolate
the malfunctioning cylinder and troubleshoot to repair the problem.
Before we start we need to know one of two things; is the engine running
poorly at idle only and seems to be ok under power? Or does the engine
run fine and it's just the engine idle condition that is the problem.
If your engine is idling rough please visit, engine misfires at idle If
your engine cranks over but won't start visit engine wont start. If
your engine won't crank over visit engine wont crank over. If your
engine is running rough all of the time or intermittently you are in
the right place. Below we have created a guide to aid diagnoses and
repair procedure for most common rough engine running problems.
- Step 1: Anytime you have a problem with
electronically controlled components such as an engine, transmission,
ABS brake, or SRS (supplemental restraint system, air bag) inspect all
fuses in the under hood power distribution center and under dash fuse
panels using a test light. If all fuses test ok continue to the next
- Step 2: To check for problems
with electronically controlled components such as an engine,
transmission, ABS brake, or SRS (supplemental restraint system) and the
fuses test ok a trouble code scan is needed to identify any system
trouble. Use a simple scanner tool to retrieve trouble codes and check
if they relate to the specific problem, like an ignition coil failure
code. If a trouble code is present but does not pertain to the immediate
problem like an EVAP code ignore it until a later time, after the
engine is running properly. The reason we repair non-related codes
after the engine is running properly is because sometime false codes
can be triggered by a rough running engine. Once the engine is running
properly the code present might cycle and turn itself off. You might
say "if the engine isn't running right shouldn't it have a check engine
light and a trouble code?" Sometimes conditions occur that will not be
detected by the computer, example: if the intake or exhaust valve
operation fails the computer cannot detect the failure because the
problem is not sensor related, so the engine doesn't run smooth and the
computer thinks everything is ok with no codes. If the trouble code
retrieved relates to a cylinder misfire like an injector driver or
ignition coil failure first repair these problems then re-test system.
If no trouble codes are present proceed to the next step.
ABS BRAKE PROBLEM COLORADO Cpmes
If the ABS light comes on, you've got trouble codes stored. Get the codes read. This is usually caused by bad wheel speed sensor, rust on the tone ring or metallic crud on the sensor
Trucks shakes engine lights comes on
You have a engine ignition miss, poss defective coil, get the trouble code out of memory to find out which cylinder is the problem, Kragen does the trouble code test for free.
Not finding what you are looking for?