2001 Oldsmobile Intrigue - Answered Questions & Fixed issues

You may have to leave the key on for more than 10 mins,leave it on until the light blinks or goes out.

Plenty of videos on youtube ! How to test an electric air pump P0410 case study

Should be at the back of the vehicle on the chassis between the wheels.

I can most likely help if I know the model. Tis posted as a 2001 olds but? thanks.

Underneath the starter

You will want to remove the upper engine torque mount and pry the engine forward to get better access at the rear cover. There is a special tool to make this easy, but can be done other ways.

That light means low coolant.

did you program the sensor

Pull it out and reinstall it. Chances are you did not get the new parts properly engaged with the opposite/complementary stops on the steering column.

Here watch this guy's video ..Maybe helpful or may not be . Chevrolet S10 P0410 Pump Problems This is on a chevy but , a GM is a GM .

The radio checks to make sure the drive capstan is turning - if not, gives the E10 error. Either the drive belt in the radio is slipping or the drive wheel in the adapter is sticking. If it does it with a real cassette, then it's probably the drive belt. If not, you can try to figure out why the wheel in the adapter is not turning freely.

could be the band end retainer take the bit to an auto specialist shop for an examination it could be part of a bolt on bit but if not it will require a new transmission housing

The seam on the windshield fluid container is broken and leaking like crazy.

It may be as simple as cleaning the battery cables.Having the clock reset shows a complete loss of voltage at one point.How old is the battery?

Those are usually located on the coolant reservoir tank.

Go on Goggle and search for OBD2 codes and you will find them. Hope this helps.

Check to see if you have brake lights, If they don't work replace the brake switch at the pedal. This will also let the shifter out of park. If they do work there is a solenoid at the shifter. Column shifters, replace the solenoid. Console shifters you have to replace the entire shift.

http://www.pdfoo.com/oldsmobile/307-11855-pdf.html

heres the link to the service manual
also you can order haynes manual for 2001 intrigue from haynes of chiltons repair manuals

This is for the manual controls and not the automatic. If you need the automatic, let me know

Turn Signal Lamps The turn signal lamps are made up of the front park/turn signal lamps and rear turn signal lamps. The front turn signal lamps flash with the rear turn signal lamps when a turn is initiated using the turn signal/multifunction lever. The turn signals will operate only with the ignition switch in the RUN position and will not operate during hazard flasher operation. When the ignition is turned to the RUN position, battery voltage is supplied to the TURN SIGNAL, CORN LPS Fuse. Battery voltage is then applied through the TURN SIGNAL, CORN LPS fuse circuit to the hazard warning switch. The hazard switch supplies a turn signal flasher signal to the turn signal switch. With the turn signal switch in the LH or RH position the corresponding turn signal indicator, rear turn signal, and front turn signal receive the turn signal switch signal and will flash. The front turn signals receive the turn signal switch signal from the turn signal switch via the body control module (BCM) . The front turn lamps are grounded at G101. The rear turn lamps are grounded at G301 and G302. Turn Signal Lamps and/or Indicators Inoperative 2

1. Turn the ignition switch to the ON position.
2. Place the turn signal switch in the LH and RH on position.

Do the turn signals operate properly? Go to Testing for Intermittent Conditions and Poor Connections yes Go to Step 3 no 3 Are all of the turn signal lamps and indicators inoperative? Go to Step 5 yes Go to Step 4 no 4 Are only the turn signal indicators inoperative? Go to Step 16 yes Go to Step 9 no 5 Check the TURN SIGNALS CORN LPS fuse for an open. Is the TURN SIGNALS CORN LPS fuse open? Go to Step 25 yes Go to Step 6 no 6

1. Disconnect the hazard switch.
2. Turn the ignition to the ON position, with the engine OFF.
3. Connect a test lamp between the ignition positive 1 voltage circuit of the hazard switch and a good ground.

Does the test lamp illuminate? Go to Step 7 yes Go to Step 27 no 7 Connect a test lamp between the ignition 1 positive supply voltage circuit of the hazard switch and the ground circuit of the hazard switch . Does the test lamp illuminate? Go to Step 8 yes Go to Step 23 no 8

1. Install a fused jumper between the ignition 1 positive voltage circuit of the hazard switch and the turn signal flasher signal circuit of the hazard switch.
2. Place the turn signal switch in the RH on position and the LH on position.

Do the turn signal lamps illuminate? Go to Step 17 yes Go to Step 15 no 9 Is a front turn signal inoperative? Go to Step 10 yes Go to Step 13 no 10

1. Turn the ignition switch to the ON position.
2. Disconnect the inoperative front turn signal lamp.
3. Connect a test lamp between the supply voltage circuit of the inoperative front turn signal lamp and a good ground.
4. Place the turn signal switch in the appropriate ON position.

Does the test lamp flash ON and OFF? Go to Step 14 yes Go to Step 11 no 11

1. Disconnect the body control module (BCM) connector.
2. Connect a test lamp between ground and the front turn signal switch signal circuit of the BCM.
3. Place the turn signal switch in the appropriate ON position.

Does the test lamp flash ON and OFF? Go to Step 12 Go to Step 22 12 Test for an open or for a high resistance in the supply voltage circuit of the inoperative front turn signal lamp. Refer to Circuit Testing and Wiring Repairs . Did you find and correct the condition? Go to Step 34 Go to Step 21 13

1. Turn the ignition switch to the ON position.
2. Disconnect the inoperative rear turn signal lamp.
3. Connect a test lamp between the supply voltage circuit of the inoperative turn signal lamp and a good ground.
4. Place the turn signal switch in the appropriate ON position.

Does the test lamp flash ON and OFF? Go to Step 14 Go to Step 28 14 Connect a test lamp between the ground circuit of the inoperative turn signal lamp and supply voltage circuit of the inoperative turn signal lamp. Does the test lamp illuminate? Go to Step 20 Go to Step 26 15 Test for an open or high resistance in the turn signal flasher signal circuit. Refer to Circuit Testing and Wiring Repairs . Did you find and correct the condition? Go to Step 34 Go to Step 18 16

1. Turn OFF the ignition.
2. Disconnect the instrument panel cluster (IPC).
3. Connect a test lamp between the supply voltage circuit of the inoperative turn signal indicator and the instrument panel cluster (IPC) ground circuit.
4. Place the turn signal switch in the appropriate ON position.

Does the test lamp flash ON and OFF? Go to Step 19 Go to Step 24 17 Inspect for poor connections at the harness connector of the hazard switch. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs . Did you find and correct the condition? Go to Step 34 Go to Step 30 18 Inspect for poor connections at the turn signal switch. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs . Did you find and correct the condition? Go to Step 34 Go to Step 29 19 Inspect for poor connections at the instrument panel cluster (IPC). Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs . Did you find and correct the condition? Go to Step 34 Go to Step 31 20 Inspect for poor connections at the inoperative turn signal lamp. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs . Did you find and correct the condition? Go to Step 34 Go to Step 32