20 Most Recent 1999 Dodge Avenger Questions & Answers


One is the missing fuel filter, clean throttle body, any codes?

1999 Dodge... | Answered on Sep 09, 2017


Fusible link 3 feeds the PCM. the ASD relay, and fuel pump relay. Assuming it has A/T, that fusible link also feeds the starter relay, the EATX-ECM, and the EATX relay. A short in any of those elements could be causing the trouble.

1999 Dodge... | Answered on Dec 16, 2016


The OBDII connector is located on the drivers (left) side under the dash within 6 inches of the steering column. It is not covered, so you should see the connector, usually attached to the lower frame of the dashboard.

1999 Dodge... | Answered on Nov 14, 2016


first place to look is under the hood on drivers side there are 3 plastic tabs that hold it on under the cover there is a diagram that shows you the fuse loction the other place to check is on the drivers side of the lower dash with the door open you will see a plastic access door you remove this with the end of your finger and there are fuses here you may need tweezers to remove the the fuse, also if you have a owners manual for the car read it it will tell you where the fuses are located , hope this helps

1999 Dodge... | Answered on Nov 28, 2015


to pinpoint a problem ,always run the fault codes first
saves time and money in the long run
but it could be low fuel pressure and the injectors not working properly

1999 Dodge... | Answered on Nov 11, 2015


I WOULD TRY REPLACING THE INPUT SPEED SENSOR..A DEFECTIVE SPEED SENSOR CAN CAUSE ALL OF THESE FAULTS..IT IS LOCATED IN FRONT OF TRANS ABOVE SOLENOID PACK..IT IS THE ONE CLOSEST TO THE ENGINE..IT SCREWS INTO TO TRANSMISSION..A 1 INCH SOCKET FITS IT..ALSO CHECK WIRING TO BOTH SPEED SENSORS..A SENSOR IS ABOUT 35 BUCKS,AVAILABLE AT YOUR LOCAL DODGE DEALER..GET A NEW ONE AND YOU'LL SEE WHAT IT LOOKS LIKE..FAIRLY COMMON PROBLEM..HAVE REPLACED LOTS OF THEM

1999 Dodge... | Answered on Nov 10, 2015


Blinking light usually means exhaust system with the shaking probably catalytic converter

1999 Dodge... | Answered on Oct 05, 2015


should say right on the dipstick. Mopar 7176 is the same as ATF+3. ATF+4 supersedes all other ATF's and will be perfectly fine in your automatic transmission.

I’m happy to assist further over the phone at https://www.6ya.com/expert/jeremy_d728a59f986299fa

1999 Dodge... | Answered on Oct 05, 2015


It will be close to the E on the guage the icon will look like a gas pump usually comes on when gauge is close to E maybe at 1/8th

1999 Dodge... | Answered on Mar 20, 2015


Disconnect the negative battery cable.
Remove the cotter pin, nut lock and spring washer.
Loosen, but do not remove, the halfshaft nut while the vehicle is on the floor with brakes applied. Raise and safely support the vehicle. Remove the wheel. Remove the brake caliper assembly and support it from the strut coil with a piece of strong wire. Remove the brake rotor. Remove the halfshaft nut and washer. Using the proper tool disconnect the tie-rod end from the steering knuckle. If equipped with abs, remove the speed sensor cable routing bracket. If you need to, disconnect the sway bar link from the damper fork. Remove the damper fork lower through-bolts and upper pinch bolt. Remove the damper fork assembly. Using the proper tool disconnect the steering knuckle from lower control arm. Remove end of halfshaft from steering knuckle, sometimes you have to a puller to it loosened.

At the other end/inboard, use a pry bar of some kind between tripod joint and transaxle, pry the joint from transaxle, be careful. when you go back with new halfshaft be sure to use proper torque specs. I copied this info from my database. I don't know tool sizes, here is where you need a basic set of tools, wrenches and sockets, standard and metric, if your going to work on your own vehicle.

1999 Dodge... | Answered on Nov 26, 2014


follow the turn signal lever toward the steering column it is right under the plastic cover of the column

1999 Dodge... | Answered on Nov 25, 2014


When a fuse blows--- I replace it--- ONLY ONE TIME

Then you know you have to get wiring diagrams of the
circuits that are on that fuse & look for where your going
to do your--- testing--- to find a problem

YOU STOP---- USING THE VEHICLE----- UNTIL RESOLVED

You also know what to do

You have a professional at a local repair shop find the problem

Do YOU PERSONALLY have another option !

1999 Dodge... | Answered on Nov 22, 2014


If you have a MIL Lamp on your dash, you have
codes in the system or data there to use

When it flashes, you do not use the vehicle

You find & repair the problems or ruin your converters
or other items

1999 Dodge... | Answered on Sep 30, 2014

Not finding what you are looking for?
1999 Dodge Avenger Logo

211 questions posted

Ask a Question

Usually answered in minutes!

Popular Products

Top Dodge Experts

Marvin
Marvin

Level 3 Expert

85239 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8984 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Avenger Dodge

  • Avenger Dodge

Most Popular Question

99 dodge avenger v6 automatic check

  • Cars & Trucks
Loading...