Go to your vehicles manufacturers web page and search for a diagram of the subject you are wanting to find info on! That's a start or you can purchase a repair manual at your parts store you can give them your cars information and they will know where to look!
To get new glass for your car, you can take a look on QualityTire Auto Shoppe for Wheels Tires Rims Auto Tint from where you will surely get collection of car accessories. Quality Tire auto shoppe also providing services on car window tinting.
the ticking noise will be from a faulty relay and will not be covered by codes. At best you will have to locate the clicking relay and replace it . IT will have something to do with the interior lights ,door switches and may be the light control module.
Hi, Leslie do you mean like how to cut a key or how to eletronic key security properties? Look in the owners manual sometimes their is a blank key that comes with car that haste the cut # on it. The 98 was the last year that electronic key lock security wasn't mandatory. If active can bee shut off by shut off by radio button controls also should be in owners manual. Good luck, feel free to ask anything about the 98 LeSabre I,m restoring one and know more than I ever wanted to
Your dealer should be able to do this, however if you have a security system VAT, you will need the system checked so you can get the correct key blank. The chip on the key creates a certain amount of Ohms of resistance, that matches your security system. If you use the wrong one the car will not start. There are methods to by pass, however you need your old key, even if its broken to do.
This can be done us small mirror. Open and pull down glove box. There is a circuit on just above controller. Remove with 10 mm socket use small tools it's tight in there. Once this is out of the way take mirror and locate rear bolt at back of box, bolts on mine were 7/16 x take you time go to junk and practice I do it all the time
Probably I would check he fuel filter by the carburetor. There is probably some contaminants in it from bad gas and you need to exchange it. It could be a silver looking item with 2 ends with fuel hose attached to it. Hope this solves your problem.
Here is a link to a how-to video, but he doesn't show you the first few steps, so, first, set parking brake, disconnect negative battery cable, raise and support vehicle. Remove passenger side wheel and then the inside splash guard in the wheel well. Remove serpentine drive belt, then remove the crank pulley. Watch the video for the rest.
crank shaft sensor replace 1998 Pontiac Bonneville 3800 motor p
You can remove the sensor and clean it, sometimes they will straighten out for a little while. Use brake cleaner to clean the sensor and gas film off the diaphragm in the small hole underneath that goes into the intake, DO NOT poke anything into that hole, or it will be ruined for sure! check the O-rings that seal it to the intake, replace if they look bad, coat with a small amount of motor oil to aid installation. Check electrical connection for corrosion, burnt wires, ect. Check vacuum hoses for cracks, splits, bad boot, holes, etc. Disconnect negative battery cable while you work on it, that will clear any codes stored that you have fixed and make the computer search for any new or different problem. No luck? - replace with new sensor. Also, check for intake manifold gasket leaks, that can cause the sensor to read wrong. With motor running, spray starting fluid (ether) around the intake gasket sealing areas. (not into throttle body) if it revs the motor up in a certain spot(s) try it a couple times there. If it continues to do that, replace the intake gasket.
study the new fender and where there is a bolt hole then that is where you will find the bolts to remove on the old fender . They will normally be along the top inside , at the bottom near the door and around the bumper and up the panel that the door hinges are attached to
the hvac selector switch in the dash may be the problem.You need to remove the switch and look at the connector on the back of switch,see if there are any burnt wires at the connector or switch.It's all electronic and the switches have been known to burn out on this and other model.
