20 Most Recent 2001 Mitsubishi Galant - Page 2 Questions & Answers

Eighth generation galant 1996-2006
2001 and 2004 should have same body interior specs

take one front seat out and if the bolt holes dont line up
you save yourself a lot of time and trouble

not many DIY car owners willing to muck around
to do interior swaps

2001 Mitsubishi... | Answered on Apr 30, 2017

Sadly this is an interference engine, meaning that when the timing belt breaks, the piston tops most likely will have hit a few valves and bent or broken them.

I'd recommend not turning over the engine any more, and taking the cylinder head off. You will then be able to assess the damage by looking at its underside for bent or broken valves. The big hope is that no pistons are holed, in which case you just need an exchange or repaired cylinder head assembly, timing belt and head gasket etc.

If any pistons are holed or cracked, they will need replacing, and when you do that you need new rings, and possibly honing of the bores.It may also lead to replacement of the big end bearings. In some cars this can be done without removing the engine, I do not have experience with your model.

For this age car you have an economic decision to make before going ahead. All the best.

2001 Mitsubishi... | Answered on Dec 20, 2016

Best thing is, go to the parts house and get a book on your car.
YouTube videos will also help.
The book is a must

2001 Mitsubishi... | Answered on Aug 30, 2016

Tell me what code you are getting .
A barometric pressure sensor dose not work on its own .
You have the mass air flow sensor this is the first air sensor coming into the vehicle then you have an air temp sensor then what is called ECT engine coolant temp sensor .
The problem to me sounds like the MAP sensor manifold absolute pressure .You loss this the vehicle is not going to run to good.
If it wore the mass air flow it would cost the most the map is far less in price still not cheap the barometric sensor it likely a symptom of the real problem .
Check the gas flow in side the engine like EGR and EVAP systems to a vacuum thing .

2001 Mitsubishi... | Answered on Jun 03, 2016

It should be located on the return side of your fuel rail , some of the Mitsubishi regulators are simple clip or three small screws to remove and replace others you have to replace the entire fuel rail depending on where it was assembled.

2001 Mitsubishi... | Answered on May 11, 2016

On either side of the headlight wiring assembly, in the engine compartment, you will find 2 small tabs. They are located to the sides and towards the bulb of the plastic assembly. Press these 2 tabs in while pulling the wire assembly out. Remove the rubber gasket and unhook the wire spring holding the bulb in place. The bulb come right out. The bulbs are halogen so do not handle the new bulb by the glass.

2001 Mitsubishi... | Answered on Apr 19, 2016

Blown head gasket letting compression into the cooling system.

2001 Mitsubishi... | Answered on Jan 19, 2016

Usually means the head gasket is leaking pressure into the cooling system, or the radiator cap is faulty.

2001 Mitsubishi... | Answered on Jan 19, 2016

time for new spark plug wires. When the wires insulation get older the resistance gets a lower ohm rating causing this to happen

2001 Mitsubishi... | Answered on Jan 04, 2016

Not finding what you are looking for?
2001 Mitsubishi Galant Logo

1,076 questions posted

Ask a Question

Usually answered in minutes!

Popular Products

Top Mitsubishi Experts


Level 3 Expert

85239 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8984 Answers

Are you a Mitsubishi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Galant Mitsubishi

  • Galant Mitsubishi

Most Popular Question

2001 mitsubishi gallant car died while

  • Cars & Trucks