2004 BMW 5 Series - Page 4 - Answered Questions & Fixed issues

the engine already seize.... recall back how the engine died last time? engine oil?

remove the starter and bench test it with your battery charger. Apply the red connector from the charger to the large battery lug on the starter solenoid. Attach the black connector from the charger to the vise. have a 6 inch wire to use now to do the test. The 6 inch wire you will apply it the red positive connector and the touch the other end of the 6 inch wire to the solenoids small threaded lug. It will click if the solenoid is good and the drive should protrude out as if it meshing with the flywheel. It should be running quite fast as well. If one or more of these explainations are now working, replace this starter. If working you have a shorted wire or a faulty electrical ignition switch

push wires onto plug no problem but its wiring code/order you need to know and this is not in any of my books so i would look for a vehicle the same in a supermarket and when owner returns ask if you can have a look at theirs or try a scrapyard and ask their .if they are the wrong way around you cannot hurt anything so you could try by elimination

IF THIS IS A TURBO, IT SOUNDS LIKE THE OIL SEAL IN THE TURBO,
KEEP A CLOSE EYE ON THE OIL LEVEL.
ROBERT

with BMW you will need the reset tool.cost in U.K.£285,or your dealer will reset it at a cost.....

It's a heavier duty battery!

Well Get Your Manual Book on the Page Setup Program Utility and Follow the instrution... Under Your Dash You Got what they Call The Terminal Box Connection For Computer Analyzer But off corse To do So .. You must bring your Car on The BMW Deeler To
Activate The Rom Memory Utility.. To Re-program your Light sensor What you call Welcome Lights On your risk Pin 2.8.13. must be short respectively with a diode 2 and 8 13 for ground. on your ignition If you miss it will just cost you S750 dollards for new computer Dash... So dont do it.. Try to re-program your Key Tranceiver some time they work Good luck

Bad battery, they go out just like that. Same thing happened to me. I got my car to the shop and they checked it out and it had a dead cell. I had enough power to run lights and radio but not enough to crank the car. If you can find a shop close they may run a new battery out to your and change the battery for free but a tip might be nice.

check fuse if not the fuse check for current to the seat motor if still no power check the switch

sounds like a grounding problem. need to check if any after market stuff was added first

some you can reset just by replacing the brake sensors, others you need a scanner.

that is a lot to ask. you must remove the rad. etc. i sugest buying a repair manual

It sounds like piston rings are worn you can try some engine restore thats what its called when you change the oil next time put that in in place of about a 1/2 of quart of oil run for 500-1000 miles and see if its better if not need to rebuild motor.

theys abouts ins thes cylinders heads. unders thes covers.

is this a common rail diesel engine ??

Will you do this picture?

And it will not be discharged battery in your car, you've written a lot of information that would clarify the problem. Where is the batteries, I will to first started!

kick car left rear tire to activate nop soun sensor.

Well, the key question is how much oil are you consuming...Quart in 600 miles or more is considered normal, but I prefer 1 quart in 2500 miles...

If high oil consumption, consider hotter plugs, and decide if engine work makes sense. If only a cylinder or two, try hotter plugs in those cylinders

If no oil consumption, look to weak spark, damaged wires, etc.

You only need to hold the left odometer reset button while turning the key to position 1 (Accessory). Keep holding the button for 5 or so seconds until any of the following shows in the display: OIL SERVICE or INSPECTION with RESET or RE. Release the button and press it again for another 5 or so seconds until RESET or RE flash. While the display flashes, press the button one more time briefly. If done correctly, END SIA should show up for a few seconds. All done.
Thank you for using fixya