20 Most Recent 2003 Mitsubishi Lancer - Page 4 Questions & Answers

I think you mean that the engine does not start first time you crank the starter. A common problem is a coil pack. If you car has a distributor, there's a coil pack inside it that is failing. Might also be the coolant temperature sensor that provides a signal to the engine computer.

2003 Mitsubishi... | Answered on Feb 23, 2015

Does this model have an ignition module? If so, they can be tested at most parts stores.

2003 Mitsubishi... | Answered on Feb 13, 2015

castor angle 1/2 to 11/2 degrees
camber 0 to 1degrees
toe in 1/8 to 1/4
As it has to be done at a wheel alignment shop they will know the best settings. Make sure that they do the alignment on the rear first as it affects the front alignment

2003 Mitsubishi... | Answered on Jan 22, 2015

could be starter or fuel pump.

2003 Mitsubishi... | Answered on Dec 17, 2014

It is pretty straight forward remove the old bags take note of anything removed and how it sets. line up the clock spring install the new air bags and then the ECU. If you install the ecu without the bags and turn the ignition on you will set the SRS light off again and need to get it reset so avoid doing so.

2003 Mitsubishi... | Answered on Dec 09, 2014

look online for a replacement and see if you can make out if its a push in type or a boyonet twist out type first of all.
Merru Xmas

2003 Mitsubishi... | Answered on Dec 07, 2014

Check if the ECU is throwing an error code. A code reader gadget will tell you if the ECU is working at all... Check and post your question again with more information.

2003 Mitsubishi... | Answered on Dec 03, 2014

Be a bit more specific: what is the problem? Drum or disk? Are you trying to put in new linings or pads, or replace a handbrake cable?

2003 Mitsubishi... | Answered on Dec 03, 2014

Sounds like the horn relay is bad, the fuse for the horn is located on the driver side look under the left of the steering wheel you will see a little compartment pull it out and you will see the fuses.

2003 Mitsubishi... | Answered on Nov 23, 2014

at the very least you will need the problem diagnosed at a reliable transmission shop , how many miles/kilometers has the vehicle done ?is it in a good service position ?

2003 Mitsubishi... | Answered on Oct 05, 2014

There are at least three possible reasons for no psi in cyl No 4.
1. Burnt or damaged exhaust valve in that cylinder
FIX Remove head and replace faulty valve
2. Blown head gasket (water mixed with sump oil shows milky on dipstick and steam or water coming out of exhaust tailpipe, radiator water disappears )
FIX Remove head, grind flat and assemble with new gasket.
3. Broken piston rings, or cracked piston or burnt hole in piston.
FIX replace faulty parts.
Squirt some sump oil ( 2 or 3 spoonfuls ) through spark plug hole,
spin motor , and if compression PSI improves then it is rings or piston, if no PSI then it is faulty ex valve !!!

2003 Mitsubishi... | Answered on Jun 27, 2014

o2 censere

2003 Mitsubishi... | Answered on Jun 24, 2014

You will find the Data Link Connector (DLC) for a 2003 Lancer, below the steering column to the left.

2003 Mitsubishi... | Answered on Jun 17, 2014

Not finding what you are looking for?

945 questions posted

Ask a Question

Usually answered in minutes!

Popular Products

Top Mitsubishi Experts


Level 3 Expert

85239 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8984 Answers

Are you a Mitsubishi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Lancer Mitsubishi

  • Lancer Mitsubishi

Most Popular Question

slave cylinder located motor

  • Cars & Trucks