20 Most Recent
2004 Mazda 6 - Page 5 Questions & Answers
Engine s running very hot and rad fan comes on ry early
On a ten year old vehicle like that, I'd say that the coolant wasn't replaced frequently enough, and the thermostat has rusted shut. Begin by flushing the cooling system, replacing its contents with PROPER antifreeze, and replace the thermostat and radiator cap.
8/13/2014 7:16:41 PM •
2004 Mazda 6
•
Answered
on Aug 13, 2014
What do these codes U0100, U0155, U0101 and P2187 mean for my mazda?
U0100 - Lost Communication with ECM/PCM "A"
U0155 - Lost Communication with Instrument Panel Cluster (IPC) Control Module
U0101 - Lost Communication with TCM
All of them are Geniric Codes 4 Mazda, I would say who ever was working on the car last, posobly forgot or missted 1 or 2 connection
plugs along the way near the last repairs. So just trace yr last steps 2 see if ther any unpluged connectors, cos looks like they all are part of same chane in that line.
P2187 - Sys To Lean at the idle Bank 1
Hope that helpes you. Good luck.
Tony D:-)
8/12/2014 3:15:53 PM •
2004 Mazda 6
•
Answered
on Aug 12, 2014
2004 Maxda 6 sputtering
hey, I own an 04 v6 mazda 6 as well and recently had that same problem. Its an ignition coil. The thing is that you have to wait until the check engine light comes on to know whick cylinder it is. I replaced all my spark plugs and boots all at once thinking it would solve the problem but it didnt work. It takes a while for the light to come on so what I did was to push my engine and make it come on. Hopefully its one of the the three coils in the front or else it would be a pain to get the back three. Each coil will run you about 50-80 dollars. Call me if you have any questions. My name is Carlos.786-210-1493
7/3/2014 1:13:41 AM •
2004 Mazda 6
•
Answered
on Jul 03, 2014
What causes the battery light to stay on after replacing battery and alternator
there may be a fuse 4 the chargeing system ,check it first if ok u may have a bad alta or bad battery or a bad ground check the battery terminals also 4 cleanness, u can take booster cables, do not use the possitive use ground cable ,one end to the ground on battery the other end to ground on motor if lite goes out then u know u have a bad ground those r a few things u can check on
6/23/2014 3:59:37 PM •
2004 Mazda 6
•
Answered
on Jun 23, 2014
Vehicle was involved in accident dealership claims
p0301=does not mean no compression,it means the computer saw a misfire on # 1 cylinder,
P0345=cam shaft position sensor bank 2,
if the timing marks are on ,i am thinking your hearing a sound of the timing being set too high and pinging under acceleration,try an experiment,refill with a higher grade of fuel for one tank to see if your noise leaves or you hear a difference.
5/22/2014 2:02:03 AM •
2004 Mazda 6
•
Answered
on May 22, 2014
Check engine light and AT light came on
First, double check that the gas cap is good and tight. Sounds silly, but sometimes a loose gas cap will cause the check engine light to come on. Failing that, take the car to someone who can read the codes. You might have a bad or lazy O2 sensor but the codes are the quickest way to tell.
5/13/2014 10:48:00 PM •
2004 Mazda 6
•
Answered
on May 13, 2014
Mazda6 CD volume goes out
I have a mazda 6 also I dont have a manual for it but I believe it is a safety feature as we get in and turn cd's up loud and I believe it is so that as we sllow down it fades so we can hear sirens etc around us. Mine fades down when I drop below 40km and gets louder agian when I get back up to 60km.
5/6/2014 10:41:41 AM •
2004 Mazda 6
•
Answered
on May 06, 2014
Not finding what you are looking for?