20 Most Recent 2000 Mazda MPV Questions & Answers

If you got misfire codes (P0300, P0301, P0302, P0303, etc.) You need to fix the misfires. See my notes at link below.

2000 Mazda MPV | Answered on Jun 17, 2019

I don't think you can replace without cloning. The vehicle will not start if code in cluster does not match ECU code. I would suggest you swap the eeproms in cluster.

2000 Mazda MPV | Answered on May 30, 2019

have someone check your ignition coil.

2000 Mazda MPV | Answered on May 01, 2019

2001 MAzda MPV- Key was stuck in ignition. Would not turn all the way back to remove. I pulled the fuse for the Hazards and WHOLA!! Key turned back and could be removed.! Just to test the problem I put the key back in , started up , pulled up and back a few feet, turned the steering wheel and parked. Key was stuck again. I pulled the fuse and again ... WHOLA! key was released. Now what I need to do is fix the problem or I have to pull a fuse every time I stop the car - ANY ADVICE??

2000 Mazda MPV | Answered on Mar 11, 2019

you should checkout this website www.reliable-store.com that has books on all vehicles, name it and they have it.

it covers wiring diagrams, electrical diagrams, fuse diagram, torque specs, PCV, error codes, fault codes, service info, repair info, owner's/service/repair/maintenance manuals etc everything totally..
I have ford expedition and I keep servicing it on my own. worth it !!!

2000 Mazda MPV | Answered on Mar 16, 2018

The grille at the base of the windshield collects rainwater and directs it through ducts in the hinge pillar to be discharged under your MPV. The ducts can become clogged with debris, causing the water to back up and leak into the interior.

2000 Mazda MPV | Answered on Mar 02, 2018

Google the vehicle or you can ask the dealer what fuse is for a specific item or check each fuse 1 by 1.

2000 Mazda MPV | Answered on Feb 06, 2018

If the 'flash' pull works it will most likely be the switch in the stalk (lever). It should be an easy enough part to get.

2000 Mazda MPV | Answered on Jan 05, 2018

code p 0106 refers to manifold absolute pressure (MAP) sensor/barometric pressure(BARO) sensor --range / performance problem=== causes ---intake / exhaust leak---wiring---MAP sensor ---BARO sensor
not shifting out of over drive could be a problem servo/ solenoid , dirty oil , wiring or VSS sensor
have that complaint properly diagnosed by a competent auto transmission specialist shop

2000 Mazda MPV | Answered on Dec 20, 2017

you can get the service and repair manual with diagram to fix the problem even you can fix it yourself because this manual help very much i had tried it even you can also so go to the given link and get it easily http://toolsnyou.com/

2000 Mazda MPV | Answered on Dec 19, 2017

I had this issue in the past. All I did was to replace the brake switch. This part is located behind the brake pedal. Btw, if you this run into this issue again in the future, you can always push this switch with your finger and it's located on top of your steering wheel enclosure, this will disengage the shifter.there is a small rectangle shape cover that you need to remove first.

2000 Mazda MPV | Answered on Oct 16, 2017

It is likely your charge wire or field circuit is shorted. If you mean you want to install an external regulator, I cannot recommend that, as it will likely cause a fault to disconnect the alternator from the computer. Trace all of the alternator wires, big and small; and I believe you will find a short. If you have an ohmmeter, use it to make sure the field power wire is isolated from chassis ground.

2000 Mazda MPV | Answered on Sep 21, 2017

Mazda MPV Automatic Transmission

TrueDelta Mazda MPV transmission Problems

A not for free link is below. However, the library application called Overdrive is likely connected to your local library. And if you have a library card, you likely will be able to use it to reach a Chilton Library held at a public library in your state. You can see if you have access to an online version of the manual. It is possible in some states.


2000 Mazda MPV | Answered on Aug 23, 2017

Those are emissions codes

2000 Mazda MPV | Answered on Aug 20, 2017

Not finding what you are looking for?
2000 Mazda MPV Logo

1,067 questions posted

Ask a Question

Usually answered in minutes!

Popular Products

2001 Mazda MPV
2001 Mazda MPV

446 Questions

2003 Mazda MPV
2003 Mazda MPV

399 Questions

2004 Mazda MPV
2004 Mazda MPV

302 Questions

2002 Mazda MPV
2002 Mazda MPV

261 Questions

1997 Mazda MPV
1997 Mazda MPV

127 Questions

Top Mazda Experts


Level 3 Expert

85239 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8984 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

MPV Mazda

  • MPV Mazda

Most Popular Question

mazda mpv 2001 not start replaced

  • Cars & Trucks