20 Most Recent 2008 Buick Enclave Questions & Answers


If you just have replaced the bulb, no need to remove the assembly. However, if the headlight needs to be removed, it is possible.
• Installing a bulb: Remove the wheel behind the headlight in question, now you would have room to change the bulb without removing headlight
• Removing the assembly: Remove the Facia and the bumper, and you can now easily remove the headlight.

2008 Buick... | Answered on Apr 29, 2020


either mp4, mov, or avi

If you need further help, reach me via phone at https://www.6ya.com/expert/joe_a79eed575e8dd8b3

2008 Buick... | Answered on Sep 18, 2019


There's a website that has all this information about all this and manuals everything totally free there are many actually but I personally like few .. let me know if u need help
thanks

2008 Buick... | Answered on Feb 26, 2019


Where an how did you find these code's ? Is it all wheel drive ?

2008 Buick... | Answered on Dec 01, 2018


Best way is to buy complete strut assemblies. They come fully assembled with new strut mount, spring, boot and strut.

2008 Buick... | Answered on Apr 28, 2018


I recently tried the DIY service and repair manuals from a website and it actually
helped me repair transmission problem in my jcb 3cx site-master. it wont move forward or reverse, engine is good both solenoids for forward and reverse work.
I don't have much technical knowledge but I just followed it step-wise, and works perfect! got it from www.reliable-store.com
All the best

2008 Buick... | Answered on Mar 22, 2018


Do you know anything about automotive electronic's ? Serial data Communication network ? Electronic module's inside the vehicle doors , communicate commands ! No relay ,no fuse .
If the passenger mirror is selected and a direction switch is activated, the DDM sends a serial data message to the PDS indicating that the passenger mirror was selected and the direction to be commanded. The PDS will then supply battery voltage and ground to the appropriate control circuits for the direction selected.
DDM - driver's door module

Door Lock System Components
The power door lock system consists of the following components:
• Driver door module (DDM)
• Passenger door module (PDM)
• Door lock relay--Located in the instrument panel (I/P) fuse block and controls the locking of the rear doors.
• Door unlock relay--Located in the I/P fuse block and controls the unlocking of the rear doors
• Body control module (BCM)
• IP BEC
• Reversible door lock actuators in each door

Power Window System Components
The power window system consists of the following components:
• Driver door module (DDM)
• Body control module (BCM)
• Passenger door module (PDM)
• Rear door power window switches
• Power window motors in each of the doors (circuit breaker protected)

Your best bet , take it to a qualified repair shop that has a diagnostic scanner that can pull code's an view input data form these systems . There is one circuit breaker for the window's an fuse's for the lock's . I would think a data network problem . But that would be a guess , without testing anything is possible on these .

2008 Buick... | Answered on Dec 27, 2017


First fix the shorted trailer lights, then check the owner's manual all fuse info is in the manual. If you don't have the owner's manual go to the GM owners website and download a free one there in pdf format.

2008 Buick... | Answered on Jul 26, 2017


It's called a Manual Shift Detent (w/Shaft Position Switch) Lever Assembly. And it's inside the transmission .
What problem are you having ? No crank , when you turn the ignition switch to the start position nothing happens ? No click ,nothing ? If your think of just replacing the switch ,stop , did you have it diagnosed ? This starting system is computer controlled .
When the ignition switch is placed in the Start position, a discrete signal is supplied to the body control module (BCM) notifying it that the ignition is in the Start position. The BCM then sends a message to the engine control module (ECM) notifying it that CRANK has been requested. The ECM verifies that the transmission is in Park or Neutral. If it is, the ECM then supplies 12 volts to the control circuit of the crank relay. When this occurs, battery positive voltage is supplied through the switch side of the crank relay to the S terminal of the starter solenoid.
DTC P0615: Starter Relay Control Circuit
have the vehicle checked .

2008 Buick... | Answered on Jun 20, 2017


well if it telling u "hood open" and hood is closed then that circuit is acting up find switch test it also check wires for lose broken eaten barewires

2008 Buick... | Answered on May 15, 2017


it may be under the back seat,,buick notorious with that..

2008 Buick... | Answered on May 10, 2017


Saying this or that is the problem won't work with your vehicle , an most all vehicle's . Given the amount of electronic's (computers C.A.N communication networks etc.. ) The BCM - body control module uses input's from ignition switch signals to determine what mode the vehicle is in . The BCM energizes relay's an sends messages on the serial data network to wake up other modules . The radio is also on the C.A.N network , signals from the BCM could be turning it on , as well as the turn signals , because the BCM functions the turn signals too .

The LT/TRN/SIG and RT/TRN/SIG fuses in the I/P fuse block supplies battery positive voltage to the body control module (BCM). When the turn signal switch is placed in either the left or right position, a signal is sent to the BCM to illuminate the desired turn signal lamps. The BCM has an internal flasher that sends an ON-OFF voltage signal to either the left or right turn signals and their instrument panel cluster (IPC) indicator. When the hazard switch is pressed, a separate ground signal is sent to the BCM to activate and flash all turn signal lamps including both IPC turn indicators. The front and rear turn signals are grounded at G401.
How to Diagnose Controller Area Network CAN

This is something best left to a qualified repair that has the proper tools to diagnose it .

2008 Buick... | Answered on Mar 03, 2017


I think i know what the issue is.. it sounds like your security system is failing. It is very common in that type of vehicle. I had the samyoue thing happen to my car. i found a module that will fix the issue, it bypasses the security system and allows your car to start every time. You can install this yourself.. Your car is on the list year make and model for this problem. Check out the site ask questions.. if you buy it and it somehow doesnt work they will refund %100. It is easy to install and they send you directions. I hope this helps ya
http://vatspasslockpasskeysecurityhelp.com/ Do It Yourself GM Security bypass

2008 Buick... | Answered on Feb 21, 2017


Do you mean that on the first few attempts the starter runs but doesn't engage the engine to turn it over? If so, you have a bad bendix in the starter or there is something preventing the bendix from moving fully into the flywheel engage position.

2008 Buick... | Answered on Feb 16, 2017

Not finding what you are looking for?
Cars & Trucks Logo

456 questions posted

Ask a Question

Usually answered in minutes!

Top Buick Experts

Marvin
Marvin

Level 3 Expert

85239 Answers

Joe Taylor
Joe Taylor

Level 3 Expert

2228 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14852 Answers

Are you a Buick Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Enclave Buick

  • Enclave Buick

Most Popular Question

replace pcv valve

  • Cars & Trucks
Loading...