2007 Mazda B3000 - Answered Questions & Fixed issues


You didn't say you had checked the spark power. No point changing stuff unless it needs changing so if the ignition is suspect always check the spark power...

2007 truck probably has plenty of electronics so check the live data and trouble codes as a first step along with ensuring routine maintenance is up to date and correctly carried out.

2007 Mazda B3000 | Answered on Dec 10, 2017 | 42 views


Chech your fuel injectors.also bleed out your fuel rail sounds like there is air inside the fuel line

2007 Mazda B3000 | Answered on Dec 04, 2017 | 64 views


if you have not yet replaced the clutch master cylinder , that will be the cause of the problem
once that is replaced the pedal will come back to correct height

2007 Mazda B3000 | Answered on Aug 05, 2017 | 185 views


if its the same code p0306 check injectors possible clogging if was a bad valve would show up more

2007 Mazda B3000 | Answered on May 04, 2017 | 247 views


if all else is in order... bring engine to tdc by marks located on main crank pulley, with distributor cap off note position which rotor is facing
should line up with no cable point on distributor.

2007 Mazda B3000 | Answered on Apr 09, 2014 | 64 views


Hi Brett, First check both bulbs, making sure they have not burned out. Second check the fuses and if all else fails check and replace the stalk switch if required. Regards John

2007 Mazda B3000 | Answered on Oct 06, 2013 | 169 views


you mean the clutch pedal? when asking questions it helps to tell which engine, trans, 4wd, 2wd, which pedal, what you have checked, ect......... ck the clutch fluid level ,you will need to replace the clutch master and slave cylinder, the trans will have to come out.

2007 Mazda B3000 | Answered on Aug 05, 2012 | 517 views


That means your engine is not heating up to working temperature or if it is the water hoses that go to the heat exchanger unit are clogged. Confirm that you engine coolant is heating up to working temperature. If not you might not have a thermostat in your cooling systrm. Insert one. If that does not solve the problem check water flow to air con.

2007 Mazda B3000 | Answered on Nov 08, 2011 | 162 views


The Camshaft Position Sensor is located within the Ignition Distributor assembly, although removeable, it is not serviced separately.

2007 Mazda B3000 | Answered on Oct 11, 2011 | 846 views


It's very possible that you have either a vacuum leak on the intake runner to that cylinder, or a faulty or plugged injector.

2007 Mazda B3000 | Answered on Sep 13, 2011 | 1,159 views


it is a hydraulic clutch it has a resavoir like your brake fluid. should be near the brake fluid res. make sure it is full. hope this helps

2007 Mazda B3000 | Answered on Sep 08, 2011 | 117 views


About what circuit? Or are you refer at firing order diagram? Keep us updated.

2007 Mazda B3000 | Answered on Jun 24, 2011 | 266 views


Check in the next diagram (click over imge for zoom)...

zjlimited_1151.jpg

Fig. Exploded view of the B Series Pick-up fuel filler assembly and pump mounting

2007 Mazda B3000 | Answered on May 01, 2011 | 803 views


Oil pan on the engine block. Torque the bolts EVENLY to 9 ft. lbs. (12 Nm) working from the center to the end position on the oil pan.

zjlimited_536.jpg

Fig. Oil pan bolt torque sequence-3.0L engine



Hope this helps (remember to rate and comment this answer).





2007 Mazda B3000 | Answered on Jan 22, 2011 | 1,037 views


Failure of head gasket between cylinder head and block.

Because oil pressure is higher than coolant pressure, oil will creep across poor sealing area of head gasket from the oil riser drilling that feeds the cylinder heads cam assembly's.

Worst case scenario would be a cracked cylinder head/s. No totally unheard of but rare.

Continued oiling of the coolant system will rot out the coolant hoses from the inside to the point they will burst.

Due to the year of this engine it may be prudent to find a used engine with less miles and swap it out.

2007 Mazda B3000 | Answered on Jan 19, 2011 | 390 views


does the transmission have a dip stick?

2007 Mazda B3000 | Answered on Jan 11, 2011 | 414 views


Just like any other car/truck, check tranny fluid while engine is hot and idling and check the transmission dipstick. Add fluid as needed into the same hole as the dipstick using a funnel. window.onbeforeunload = function() {}

2007 Mazda B3000 | Answered on Jan 10, 2011 | 919 views


The PCM fuse controls the light, but that'll keep it from starting. If you don't fix the issue and clear the light, it'll just come back on in about 50 or less depending on what the issue is. It is actually illegal to clear a light without fixing the problem. If it really bothers you, you could always just take the bulb out.

2007 Mazda B3000 | Answered on Nov 27, 2010 | 240 views


might be fluid but here are some helpful websites, Good Luck Tim:

http://www.automotive-clutches.com/basic_clutch_info.html
http://www.aa1car.com/library/2003/bf50332.htm

2007 Mazda B3000 | Answered on Oct 23, 2010 | 275 views


Technical Description:
EVAP Control System Canister Vent Solenoid Circuit Malfunction
The EVAP system monitors the canister vent (CV) solenoid circuit for an electrical failure.
The test fails when the signal moves outside the minimum or maximum allowable calibrated parameters for a specified canister vent duty cycle by PCM command.
Symptoms: You will likely not notice any drivability problems.
Causes: A code P1451 may mean that one or more of the following has happened:
*VPWR circuit open
*Damaged canister vent solenoid
*Canister vent solenoid circuit open or shorted to ground, power, etc.
*Damaged Powertrain Control Module (PCM)
*Possible SolutionsVerify canister vent solenoid - To verify normal functioning, monitor the EVAP canister vent solenoid signal PID EVAPCV and the signal voltage
(PCM control side).With the valve open, EVAPCV indicates 0% duty cycle and a voltage approximately equal to battery voltage.
When the valve is commanded fully closed, EVAPCV indicates 100% duty cycle, and a minimum voltage drop of 4 volts is normal.
Output test mode may be used to switch output on/off to verify function.
*Replace canister vent solenoid

Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question&&&&

2007 Mazda B3000 | Answered on Sep 29, 2010 | 619 views

Not finding what you are looking for?
Cars & Trucks Logo

Popular Tags

106 questions posted

Ask a Question

Usually answered in minutes!

Popular Products

2004 Mazda 6
2004 Mazda 6

738 Questions

2000 Mazda MPV
2000 Mazda MPV

690 Questions

1999 Mazda 626
1999 Mazda 626

545 Questions

2001 Mazda Tribute
2001 Mazda Tribute

604 Questions

2002 Mazda Tribute
2002 Mazda Tribute

613 Questions

Top Mazda Experts

Marvin
Marvin

Level 3 Expert

85239 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14852 Answers

Arnie Burke
Arnie Burke

Level 3 Expert

6528 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...