Top 20 2005 Seat Alhambra 2.0 Questions & Answers

this indicator for water at fuel filter . or make sure brake lights is ok if not replace brake s.w

-Check in its manual. Good Luck mai

-Make sure coolant is full then erase the code. Good Luck Mai

replace gear lever s.w .

It means the engine oil pressure is below a safe reading as sensed by the gauge and light sending unit on the engine. DO NOT DRIVE THIS UNTIL THE PROBLEM IS REPAIRED.

usually if this light comes on its to late and your engine will have considerable damage.. if it's a sensor failure then you need an oil pressure sending unit. they are fairly inexpensive and can be found on the oil filter adapter housing

Check to see if brake lights work, If not replace brake fuse, should work

The diagnostic process for the heating and cooling is a very long and involved process and requires a couple of specialized diagnostic tools that you may not have. Here are some of the easier things to physically check, which can be preventing the proper function of the seats: Mechanical

• Seat track

• Climate controlled seat ducts

Electrical

• Climate controlled seat ducts
• Fuse(s)
• Circuitry
• Driver seat module (DSM)
• Lumbar control switch
• Memory set switch
• Power seat motor
• Seat control switch
• Seat fan motor
• Climate controlled seat module
• Climate controlled seat switch

Question edited for clarity. There are only a two relays in the box, but not listed for the wiper. This usually means that the wiper is either not covered by a relay or it is a function of the Body Control Module. There are fuses listed.

SEAT Altea (2005-2015) fuses

Fuse Box Diagrams https://fuse-box.info > seat > seat-altea-2005-2015-fuses The fuse box is located in the left side of dash panel, under the steering wheel. The location of the fuses in the ... ..

If your wiring is OK, I would suspect the switch.

If your John Deere 4600 shuts off when put in gear, even after bypassing the seat switch, there could be several potential causes for this issue. Here are some troubleshooting steps you can take:

1. Check the Neutral Start Switch: The neutral start switch ensures that the tractor can only be started when it is in neutral. If this switch is malfunctioning, it may cause the engine to shut off when you engage a gear. Inspect the switch for any visible issues and consider testing or replacing it.
2. Inspect the PTO Switch: The power take-off (PTO) switch should be disengaged when shifting gears. A malfunctioning PTO switch could be causing the engine to shut down. Check the PTO switch for proper operation.
3. Examine Safety Interlock Switches: There are often multiple safety interlock switches on a tractor, including those associated with the brake, clutch, and other safety features. Check all safety interlock switches to ensure they are functioning correctly. A faulty safety switch could shut down the engine when a gear is engaged.
4. Battery Voltage and Connections: Low battery voltage or poor connections could lead to electrical issues. Check the battery voltage and ensure that the connections are clean and tight.
5. Inspect Fuses: Check the fuse box for any blown fuses. If a critical fuse is blown, it could lead to a shutdown when engaging gears.
6. Fuel System: Ensure that the fuel system is functioning properly. Check the fuel filter, fuel lines, and fuel supply to the engine. Lack of fuel flow could result in the engine shutting down.
7. Engine Sensors: Modern tractors are equipped with various sensors that contribute to engine control. A malfunctioning sensor, such as a crankshaft position sensor, could cause the engine to shut off unexpectedly.
8. Professional Inspection: If the issue persists after checking the above components, it may be advisable to seek professional assistance. A qualified mechanic or John Deere service technician can perform more in-depth diagnostics using specialized tools.

It's important to approach these troubleshooting steps carefully, and if you're uncertain or uncomfortable performing certain tasks, seek assistance from a professional. Additionally, refer to the tractor's manual for specific details about the safety interlock system and troubleshooting procedures.

You have an old Spanish Seat (pronounced See-At) car with a manually adjustable seat? You can still get spares for them because the company is a government enterprise. https://www.google.com/search?q=seat+car+spares ..

One of these may help. The instructions may not apply to your year but one set may suffice. Remove back seat of Chevrolet Malibu #chevrolet #malibu - YouTube Back Seat Removal for cover install ' Chevrolet Malibu Forums (chevymalibuforum.com) How to remove back seat Chevrolet Malibu ? (victoriamgclub.com)

What model and year of Seat car. https://www.google.com/search?q=seat+uno+car+remove+seat+cover ..

Year make and model of your Spanish made Seat car. The latch hooks can be adjusted.

https://video.search.yahoo.com/search/video?fr=mcafee&p=05+tahoe+power+seat+relay+location&type=E210US1494G0#id=11&vid=582c73d39fbe565871f87a96e85221a9&action=view

Your best bet is to get a good used part from a salvage yard. I doubt that GM still services the part individually.

Unfortunately there isn't one. Contact Pride direct https://www.google.com/search?q=pride+sidekick+wiring+diagram ..

James, Here's some sites that will help you... https://www.google.com/search?q=driver+side+power+seat+on+2003+navigator+not+working Best to you.

Posting an answer as a follow-up doesn't work on Fixya because posts are not threaded by User. This question has no context to any previous questions and answers.The correct way is to click COMMENT under the answer of the person you wish to reply to, in this case our Expert, Steve Pack.HOWEVER. I looked at your posting history and I don't see any replies to you from Steve!! There are two possible reasons!. You posted Anonymously, in which case it doesn't show on my history. It will show on yours though. Go to that question and reply.2. You read a SUGGESTED Answer where someone else asked a similar question and Steve replied.One major benefit of doing it the right way is that Steve would get a Notification that someone had replied and needed further help. Doing it your way, it would be pure luck if he saw it. I came across a post made in a similar way referring to me by name and it was made over a year previously!!https://www.fixya.com/users/james-i-yorkIn your questions you had contact with our Expert Jeff Armer. He is a full time master auto electrician and the best one to reply to by clicking Comment under his Answer. He is a great guy and I noticed you didn't thank him :>(..