20 Most Recent 2004 Proton Gen-2 Questions & Answers

Replace relay that is UNDER the engine bay Fuse Box. It has no fan switch. Fan relay controlled by ECU.

2004 Proton... | Answered on Jul 01, 2019

The pistons in the caliper should retract without much effort. A "C" clamp is usually all you need to do it. I suspect you have a seized caliper or possibly a kinked or crushed brake line (preventing the brake fluid from returning to the master cylinder when the piston is depressed) feeding that caliper - but isn't very likely.

2004 Proton... | Answered on Aug 16, 2016

google you may be able to down load a pdf for a fee, if
you can't find it free from the MFg or distributor.

2004 Proton... | Answered on Dec 22, 2014

It can only be a problem caused by a shortage, the wire activated by the brake as you apply the brakes is shorting ( touching) the other wires in the wiring loom, hopefully not too far down , unless you are competent and confident with a cars electrical circuit I would seriously suggest you get an auto electrician. B4 that Have a look and follow the brake pedal wire ( situated maybe on the floor of the car and activated as the brake pedal is pressed or on the pedal itself, )look for anywhere tge wire is bare ( without insulation ) then rectify and all should be OK , If you cannot see an easy fix get an auto electrician, get a call out , not a auto shop /garage he will be cheaper.

2004 Proton... | Answered on Aug 02, 2014

If your car has automatic gears , and your problem as if it is going uphill then you obviously have a faulty automatic transmission box , this can be fixed by a competent mechanic but would be better to take it to an auto-mechanic, for a replacement gearbox or it may just be a missaligned gear selector in the gearbox, it will be expensive whatever the problem is ........unless the auto-mechanic is your best buddy..............................Sorry

2004 Proton... | Answered on Jul 23, 2014

If it's auto, get it scanned for error codes before you do anything with the wires. The codes will guide your repair better.

2004 Proton... | Answered on Jun 13, 2014

Replace brake pads for both sides.

2004 Proton... | Answered on Jun 13, 2014

It is an integrated model.The TPS is part of the motorized throttle body. If you have TPS error code. Clean the throttle body and reset it with a good scanner. If that does not work, you may have to replace it.

2004 Proton... | Answered on Jun 13, 2014

Inertia switch is only relevant when you have a collision and the engien does not start. Fuel pump may not run and coils no spark. If not, same thing could also happen if the immobilizer is not disabled or the key FOB gets damaged. The ignition key has an RFID chip in it and if you drop your key or remove this chip, the car will not recognize the key and wont start. You need to use your spare key from then on.

2004 Proton... | Answered on Jun 12, 2014

Hi simba, the maximum torque on a SP4H is 148 Nm at 4000 rpm.

2004 Proton... | Answered on Apr 11, 2014

We do not have this make so I can only provide a general description of the codes meaning and poss causes.
P0108 - Manifold Absolute Pressure/Barometric Pressure Circuit High Input

Possible causes- Manifold Absolute Pressure harness is open or shorted
- Manifold Absolute Pressure sensor poor electrical circuit connector
- Faulty Manifold Absolute Pressure sensor
- Faulty Powertrain Control Module (PCM) or Engine Control Module (ECM)

2004 Proton... | Answered on Jul 23, 2012

P1070 is not a valid code in my books, but this is not a make sold in my country (USA) so it may be unique to this far east make of car.

2004 Proton... | Answered on Jun 15, 2012

Not finding what you are looking for?
2004 Proton Gen-2 Logo

Popular Tags

27 questions posted

Ask a Question

Usually answered in minutes!

Popular Products

Top Proton Experts


Level 3 Expert

85239 Answers


Level 3 Expert

3063 Answers

john h

Level 3 Expert

23504 Answers

Are you a Proton Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Gen2 Proton

  • Gen2 Proton

Most Popular Question

p0108 manifold absolute pressure map

  • Cars & Trucks