20 Most Recent
2007 Pontiac G6 Questions & Answers
Pontiac G6 manual transmission level
check by placing your finger into the filler plug hole and seeing if you get some fluid onto the end of your finger. If you don't, then the fluid is low. If there is fluid at that level, then no additional fluid is needed.
Fuel tank pressurre sensor replacement
It is located on top of the fuel sending unit on the fuel tank. The tank needs to be dropped in order to service the pressure sensor. It's not real common for them to go bad and there are several other possibilities that can make this code appear. It may be worth checking them out also.
It would be nice if you could oust the actual code you are getting also. I’m happy to assist further over the phone at
https://www.6ya.com/expert/jeremy_d728a59f986299fa
2007 pontiac windshield wipers stopped working and you can hear the motor still runs
Wiper Motor
- Remove finish caps.
- Make reference marks for installation and remove wiper arms.
- Remove the air inlet grille panel.
- Remove the bolts attaching the wiper module to the plenum.
- Carefully lift the wiper module out of the plenum.
- Disconnect the electrical connector from the wiper motor.
- Disconnect the clip retaining the electrical harness to the wiper module.
- Remove the wiper module assembly from the vehicle.
- Remove the wiper motor.
Wiper module assembly and motor removal
To install:
- Install wiper motor and mounting bolts, tighten to 40 inch. lbs.(4.5 Nm).
- Connect the electrical connector to the wiper motor.
- Connect the clip retaining the electrical harness to the wiper module.
- Position the wiper module assembly into the plenum.
- Install the fasteners attaching the wiper module assembly to the plenum, tighten fasteners to 89 inch. lbs. (10 Nm).
- Install the air inlet grille panel.
- Install wiper arms and align to reference marks.
- Tighten wiper arm retaining nuts to 26 ft. lbs. (35 Nm).
- Install finish caps.
https://www.youtube.com/watch?v=dHJli8z1_jI
https://www.youtube.com/watch?v=A3hLLrwz8wQ
How do i remove bcm in 2007 pontiac g6?
Why ? If you replace the BCM it will need to be programmed . Dealer !!
This vehicle's body control module (BCM) has a bussed electrical center integrated into the housing. Body control relays and fuses are installed directly on the BCM, which simplifies wiring and junction blocks on the vehicle. The body control system consists of the BCM and its associated controls. Battery positive voltage is provided to the BCM from IBCM BATT 1 fuse and the IBCM BATT 2 fuse in the underhood fuse block. The module grounds are wired to ground G201, G203 and G305. The BCM is wired to the GMLAN High speed serial data buss, and the GMLAN Low speed serial data buss, as well as discrete input and output terminals to control the functions of the vehicle's body .
Trying to save you some agravation an wasted time an money . For a do it yourselfer , this is nothing you should be messing with ! You don't have the training to be messing with the BCM .
A new body control module (BCM) must be programmed with the proper regular production option (RPO) configurations. The BCM stores the information regarding the vehicle options and if the BCM is not properly configured with the correct RPO codes the BCM will not control all of the features properly. The Tech 2 software will automatically prompt you with the various RPOs available for the vehicle. Ensure that the following conditions exist in order to prepare for BCM programming:
This entire procedure has been reviewed before starting
The battery is fully charged.
A CANdi module is installed between the vehicle and the scan tool.
The ignition switch is in the ON position.
The data link connector (DLC) is accessible.
All disconnected modules and devices are reconnected before programming.
Not finding what you are looking for?
Wiper module assembly and motor removal
To install:
https://www.youtube.com/watch?v=dHJli8z1_jI
https://www.youtube.com/watch?v=A3hLLrwz8wQ
