2005 Mazda B3000 Cab - Answered Questions & Fixed issues

Even when you remove the ABS, your break won't work on the one wheel. You should look for the real cause of the break problem, not start unplugging fuses. When you disable the ABS, the only thing that happens is the wheels can block, while using the breaks. If already one wheel does not break, you run in even more trouble then before.

Po113 is the air temp code it was not transferred from old air cleaner po102 is a air flow code set from over oiling the new filter. the engine still will never rev over 3,000 rpms due built in rev limiter to stop over reving with no load.

If you mean the scanner is not working, check the cig lighter fuse first.

It can be issue with IAC( idle air control valve) causing the problem.

There are many other possibilities causing these idle issues. Engine idles rough.

There are few help links with solutions to troubleshoot such idle issues.

I suggest you refer the link below and follow its troubleshooting details:------

Click the link below:-----

Ford Expedition IAC valve replacing

http://technoanswers.blogspot.com/2012/12/ford-expedition-iac-valve-replacing.html

Bad miss at idle?

http://technoanswers.blogspot.com/2012/01/bad-miss-at-idle.html

-----------

Stumbling and stalling at idle after engine rebuild?

http://schematicsdiagram.blogspot.in/2012/03/stumbling-and-stalling-at-idle-after.html

------------

1999 Ford F-150 Idles rough and quits when gas pedal is pressed less?

http://technoanswers.blogspot.in/2012/01/1999-ford-f-150-idles-rough-and-quits.html

---------

Engine stumbles coming off idle when warm?

http://repairhelpcenter.blogspot.com/2012/01/engine-stumbles-coming-off-idle-when.html

------------------

Erratic idle on car?

http://schematicsdiagram.blogspot.com/2011/12/erratic-idle-on-car.html

-----------

Cold start problem and vehicle shudder around 2500 to 3500 rpms

http://repairhelpcenter.blogspot.com/2012/10/cold-start-problem-and-vehicle-shudder.html

----------

Low idle when cold out side?

http://repairhelpcenter.blogspot.com/2011/12/low-idle-when-cold-out-side.html

-----------

GMC Sonoma Stalls and idles low

http://technoanswers.blogspot.com/2012/10/gmc-sonoma-stalls-and-idles-low.html

--------

GMC Idle Air Control (IAC) Valve Replacing?

http://schematicsdiagram.blogspot.com/2011/12/gmc-idle-air-control-iac-valve.html

-------------

1996 Camry intermittent engine failure while idle?

http://repairhelpcenter.blogspot.com/2011/10/1996-camry-intermittent-engine-failure.html

------------

Engine quits at idle?

http://repairhelpcenter.blogspot.com/2011/10/engine-quits-at-idle.html

-----------

Car overheats and Air blows hot at idle?

http://howtobyme.blogspot.com/2011/11/car-overheats-and-air-blows-hot-at-idle.html

---------

High Idle Problem

http://repairhelpcenter.blogspot.com/2012/10/high-idle-problem.html

-------

While stop engine idles like cylinder missing?

http://schematicsdiagram.blogspot.com/2012/01/while-stop-engine-idles-like-cylinder.html

---------

Idle flair is noticed on car? Rough idle? car will not idle? Erratic idle speed?

http://technoanswers.blogspot.in/2012/02/idle-flair-is-noticed-on-car-rough-idle.html

--------

High rpm in neutral? Inconsistant high RPM in neutral?

http://technoanswers.blogspot.in/2012/02/high-rpm-in-neutral-inconsistant-high.html

-------

Vehicle stumbling at idle and shows code 54?

http://schematicsdiagram.blogspot.in/2012/03/vehicle-stumbling-at-idle-and-shows.html

----------

Rough idle, staling and Erratic shifting?

http://technoanswers.blogspot.in/2012/03/rough-idlestaling-and-erratic-shifting.html

-----------

While stop engine idles like cylinder missing?

http://schematicsdiagram.blogspot.com/2012/01/while-stop-engine-idles-like-cylinder.html

---------

These details will help.

Thanks.

check the dpfe sensor ,it works in conjunction with the egr valve,it measures exhaust back pressure

EGR Valve?

Step 1 torque to 59 ft pounds
2. Loosen one full turn
3. 37 ft pounds
4. 68 ft pounds

Use torque sequence below

Dan writes Daniel Cleaveland Nov 03, 2022 What happened here? I am currently trying to remove star bolt holding tensioner on, it is not budging. I'm guessing from this post I will not get an answer anytime soon. The T45 fit, then T50, I am going to go find a T55 and T60 I suppose. I am definitely wondering if I am doing something wrong with this one bolt holding me back from 4 more to replace water pump. ============================================== It all depends on whether anyone sees questions and if anyone is qualified to answer or wants to try. I try most. Did you consider the bolt might be a left hand thread? Look at the normal rotation, this should tighten the bolt not undo it. There is a video but it looks too short. https://www.google.com/search?q=1994+Mazda+B3000+Removing+a+belt+tensioner ..

Hi there my name is Brandon I am a mechanical n electronic engineering technician its is one of two places on the kick panel on the inside on past... side or at the back up top next the tank

There's a website that has all this information about all this and manuals everything totally free there are many actually but I personally like few like reliable-store .. let me know if u need help thanks

Fix your car right away by clicking the link I attached Mazda B3000

Sounds like the pop off valve in the intake duct is stuck open, it is dumping boost pressure. Check boost pressure on the dash gauge.

• Starter Mounting Bolt, Type 1, M10-1.5 X113mm And M10-1.5 X45mm, Gm 2,2.5,3.4 L
• Thread Size: M10-1.50
• Length (In): 1.770 And 4.450 Inch
• Length (mm): 113mm

You can put it on standby mode by holding the alarm reset button down while turning the key back & forth from off to on in the ignition twice. try it its worked before

ford ranger

Looks like a black - light green wire feeds the radio and wipers.

4th gear gone transmission shop to chk maybe a sensor

Either the starter solenoid is shorted to power or the electrical portion of the ignition switch has shorted to the start position.

that is illogical. the issue has to be with the gas tank repair. u need to get the air out of the gas line, or u missed replacing some wiring - but since the motor runs i'm going with air.

you can check for power at the large wire on the starter it should have battery voltage all the time and the small wire on the starter should only have power when someone is trying to start the car. if you have this then the starter is bad.