20 Most Recent 1989 Lotus Esprit - Page 6 Questions & Answers

I need to wire a jayco caravan tail/indicator light set Navara p/no 86050 from old type set-up

visit any camping supply dealer

Cars & Trucks | Answered on Jan 06, 2021

What Will A Roof Inspection Cost?

I am In Australia and just paid $160 for a roof inspection and report.
It was $400 for a full house inspection and report. Both these costs were fairly similar to two other quotes. Cheers Bob

Cars & Trucks | Answered on Jan 06, 2021

2 Answers

Toyota losing power when going uphill

Is the catalytic converter plugged? have a exhaust back pressure test run.

Cars & Trucks | Answered on Jan 06, 2021

1 Answer

My truck won't turn over

Flat battery

Main battery fuse

Antitheft system

Starter

Ignition switch

in that order

Cars & Trucks | Answered on Jan 05, 2021

1 Answer

Sparks are showing when running ..KDE6700TA I did removed AVR and regulator for test again ...but the sparks is the one that got me ! Was told that the coil or the inside rotor had to be replced ...never worked on this gen. before Thanks for any help i can get !

Definitely I changed mine recently my regulator and it started

Cars & Trucks | Answered on Jan 05, 2021

1 Answer

NP200. Why is cam timing 7 teeth out when No 1 cylinder is at TDC?

You are at the wrong stroke on the 4 stroke engine. You have to be at TDC on the COMPRESSION stroke. You are at inlet or exhaust stoke TDC :>)

Cars & Trucks | Answered on Jan 05, 2021

1 Answer

I swap my VOXY 2003 engine 1AZ-FSE the NOAH 2002 engine and I unplug the ECU then after installing it back and it won't start. What happened ?

It is difficult to guess - it is presumably the original ECU that goes with the car that is coded to that VIN and will talk the same language as the other modules?

Poor connections are possible, the current and voltage on some of the pins is very small so dust can stop data reaching the ECU. The exposed terminals of the ECU and socket can quickly form an oxide coating that also resists the flow of current.
Touching the exposed pins, if you are the sort of person that charges with static electricity, can damage the ECU.

It could of course coincidentally be something entirely different, the immobiliser failing to disarm perhaps. Time to find a wiring diagram and begin checking voltages, continuity, etc.

Cars & Trucks | Answered on Jan 05, 2021

2 Answers

What is P0301

google it up

Cars & Trucks | Answered on Jan 05, 2021

1 Answer

#1 I was rear ended in my tj wrangler & right after impact it would not turn over but still had power. My fuel tank was smashed forward into my rear axle but didn’t actually crack the tank or deform it. Anyway i’m not sure if the inertia switch is all i need to worry about or if there is lines that could be smashed as well. I need to know where the inertia is located and I would appreciate any feedback!

There is huge risk for damaged lines, etc. This vehicle needs to be closely inspected. Alignment is now an issue.
Needs quality inspection.

Cars & Trucks | Answered on Jan 05, 2021

2 Answers

Hello just took my 88 cavalier to be smog tested and it failedthe tech said its starving for fuel i can check all the obvious issues first if none of these troubleshoots dont work then what does a man do please help i love this car hate to hsve to sell it back to the state

I suggest you have a fuel pressure and delivery volume test carried out and then pull the injectors for testing - once you are certain the fuel system is capable of delivering the fuel in a form that is readily burnable, any remaining problems are likely to be tired sensors. Bad spray patterns can sometimes not burn very well and be seen by the management system as a lean mixture.

Cars & Trucks | Answered on Jan 05, 2021

2 Answers

I have 2008 Chevy impala LT with Flex fuel why does it have 2 MAP sensors?

https://www.rockauto.com/en/catalog/chevrolet,2008,impala,3.5l+v6,1440297,fuel+&+air,manifold+pressure+(map)+sensor,11207
Map sensor and connector.
2 Map sensors?

Cars & Trucks | Answered on Jan 04, 2021

1 Answer

Vauxhall Meriva. What causes 'BATTERY' light to come on?

Seems to be a known fault on that model!

https://www.google.com/search?q=vaxhall+meriva+battery+light+comes+on

.
If you see your Meriva's battery light turns on while the engine is already running, that is a strong indication that the alternator is no longer providing enough wattage to power the various electrical systems and charge the battery at the same time. A new alternator will rectify the problem.Dec 3, 2019

Opel Meriva: Battery Light On - Diagnosis ' Drivetrain Resource

Cars & Trucks | Answered on Jan 04, 2021

1 Answer

I have no battery opening tools for the Orbit NAHRLED4 remote car starter Fob. What do they look like??

usually a small screwdriver will do

Cars & Trucks | Answered on Jan 04, 2021

1 Answer

How do I change the battery for the Orbit NAHRLED4 remote car starter Fob. Picture attached.

Firstly, place the orbit in between the two battery opening tools.
Then twist the top battery tool anti-clockwise to open.
Open the Orbit and detach the old battery from the inner casing.
Place the new battery with the plus symbol (+) facing downwards.
Push the top and bottom Orbit shell together.

Cars & Trucks | Answered on Jan 04, 2021

1 Answer

The steering wheel in my 08' g6 continues to lock up as I'm turning, despite having changed the power steering motor and the rack and pinion. Ive also checked all the fuses. Each time I change anything it acts fine for awhile but after a couple hours of driving reverts back to the steering wheel locking up on me in a turn

I would check for a poor ground in the power steering motor circuit.

Cars & Trucks | Answered on Jan 04, 2021

1 Answer

Craisler 300 2007 tcm locations

no such make

Cars & Trucks | Answered on Jan 04, 2021

1 Answer

What side of the engine are the welsh plugs

This will depend on the exact engine you are using. Comment below with the make, model, year and fuel type of your vehicle. I can help you better with that information.

Cars & Trucks | Answered on Jan 04, 2021

1 Answer