20 Most Recent 1978 Ford LTD - Page 9 Questions & Answers

If the engine is covered by warranty, I would get both of them replaced, (depending on the engine) as there is an issue with the early design. The dealership will try to fob you off as it is a horrible job.

Belt diagram for 99 5.4l engine

I suggest you take your car to a certified Ford mechanic to diagnose the issue. In the meantime, here are some possible causes of the problem: Blown fuse: Check the fuse box and replace any blown fuses . Faulty flasher relay: A faulty flasher relay can cause the indicators to stop working. A mechanic can replace the relay if necessary. Bad bulb: Check the bulbs and replace any that are burnt out or damaged . Defective connector: Check the connectors between the flasher and the switch. If they are defective, they may need to be replaced.

https://www.justanswer.com/ford/m539u-blowing-pcm-fuse-1997-ford-ranger-2wd-3-0-soon.html

Definition of check engine code P0443:Generic (Common for all car manufacturers):Evaporative Emission System Purge Control Valve CircuitWhere do you get cam sensor from I wonder.Purge valve stuck open and the engine will get incorrect mixture then stall.

Check the fuel pump relay switch. According to a post on the Ford Truck Enthusiasts Forums, the fuel pump relay switch is located under the PDB (Power Distribution Box) . You may need to refer to the wiring diagram to locate it. If you don't have one, you can request it from the same post. Check the fuel pump cutoff switch. This switch is located behind the firewall and is designed to shut off the fuel supply in case of an accident . Check the fuel rail pressure regulator. If the fuel pump and the fuel cutoff switch are working fine, then the problem might be with the fuel rail pressure regulator. This is a small can mounted inline with the fuel rail with a vacuum hose attached to a hose barb on top of the unit .

Question edited for clarity. It is a known issue on it. https://www.google.com/search?q=2010+Ford+Figo.+speedometer+not+working ..

fel_pro_torque_specs_guide.pdfhttps://3f447m28lzom2c10ov383c38-wpengine.netdna-ssl.com/wp-content/uploads/2015/01/AERATorque310.20.14.pdf

I had overheating problems with a ford figo and after looking and asking for answers out of frustration i took the car to a Ford garage , they did a combustion test on the head and found the head had overheated.To make the story short i found out the Ford figo got an aluminium head and block, when it overheats it gets disformed the only way to fix it was to skim the head and the block.

So there are multiple transmission types that could be in your vehicle depending on what engine you have. The 4 cyl would have a FNR5 transmission - A 5 speed automatic from Mazda and the V6 would use the Aisin AWF-21 6-speed. To access the SSF on the FNR5 you need to remove the side cover located on the back for the transmission by the firewall. The are 2 solenoids located under this cover and the SSF will be the smaller of the 2 and should have a normal Ohms reading of 8.4-21.8 Ohms when testing. The AWF-21 does not have a SSF so I don't believe this is the transmission you have but if it is let me know and I can try to figure out what solenoid you might be looking for.

google 1994 ford mercury sable fuse box diagram copy and paste https://fuse-box.info/mercury

Question edited for clarity and translated to written English. Your scanner isn't good enough. The scanner should run when the car is on and you should be able to clear the code. You need an auto electrician with a professional quality scan tool computer that can read historical codes that aren't being displayed. If the CEL is on, there is a code. https://www.google.com/search?q=auto+electrician+near+me ..

Probably a broken wire under the seat. B2312 is a software issue, possibly caused by no comms. B2320 is a head rest issue, probably a broken wire or even water ingress.

If the smoke from the exhaust pipe is either grey or bluish-tinged, it generally means that your engine is burning oil inside the combustion chamber. Burning oil could be due to a number of causes, from leaky valve seals to bad piston rings. take to reputable repair shop

Driver side, underneath dashboard, between the driver- side door and steering column area.

You should have very few problems. It is old enough that the ECM should accept a bigger engine, if not you will need the ECM from the vehicle the engine came from. https://www.google.com/search?q=Ford+Cortina+MK+V+with+3+litre+V6 ..

It is a known issue https://www.google.com/search?q=2005+Ford+Freestar+Van+%2F+with+power+door+locks.+Smart+Junction+Box ..

In that year model, Ford didn't call it a body control module. They called it a smart junction box and it's located in the right kick panel

Wiring diagrams usually are around 100 pages. Nobody is gonna send you that. If you tell us what you need we can probably send you the diagram for that