20 Most Recent 2010 Ford Fusion 2.5 Questions & Answers


The SJB supplies power to the interior lighting system. The SJB will set DTCs if certain circuit failures exist with the interior lighting system.
Visual Inspection Chart Mechanical Electrical
  • Courtesy lamps
  • Map lamps
  • Luggage compartment lamp
  • Vanity lamps
  • Glove compartment lamp
  • Smart junction box (SJB) fuse 3 (15A)
  • Circuitry
  • Courtesy lamps
  • Map lamps
  • Luggage compartment lamp
  • Vanity lamps
  • Glove compartment lamp
  • SJB

Check fuse # 3 SJB

2010 Ford Fusion... | Answered on Jul 07, 2017


could be a dry spring or pedal bush at the top of the pedal
if it is a cable operation , could be a failing cable

2010 Ford Fusion... | Answered on Mar 31, 2016


If your only having a problem with the plug have a machinist work on it, he can remove your stripped bolt by drilling it out, if the pan thread is stripped on an aluminum pan a new helicoil insert can rebuild your pan thread.

2010 Ford Fusion... | Answered on Mar 08, 2016


You may have a bad Throttle body.

2010 Ford Fusion... | Answered on Oct 17, 2015


replace window motor it should come with the window regulator as well. it takes more power to push window up then down. wore out motors will act like this. the fact that it trys at all tells you the switch,relay and circit breaker are good

2010 Ford Fusion... | Answered on Mar 26, 2015


change your gas filter it might be clogged the red x might have cleaned all the dirt in your system and has now clogged the filter the car starts runs for 10 - 15 seconds then stalls out ? if this sounds like your car I also see you are using the term petrol so I know this is a diesel car / or are you just using that term for gasoline there's a big difference between fuels please post back to clarify fuel use?

2010 Ford Fusion... | Answered on Feb 25, 2015


Not usually, get a meter that measures amps. Hook it into the system by removing the negative battery cable and hook the meter to the battery on one lead and the cable on the other lead. Measure the amperage. Then start pulling fuses out of the fuse box and see what makes the reading drop. NOTE that opening the door will cause a big amperage draw. You could blow out the meter if you have it set wrong or it is not high amp rated

2010 Ford Fusion... | Answered on Feb 07, 2015


You will have to remove the door panel from the inside. Once you have the door panel removed you can manually work the linkage to open the door.

2010 Ford Fusion... | Answered on Oct 14, 2014


YOUR VEHICLE NEEDS TO BE DIAGNOSED TO SEE WHAT THE PROBLEM IS BEFORE ITS TOO LATE.yOU COULD HAVE A BAD SOLINOID , WHICH IS MAKING IT SHIFT IN A ODD MANNOR,DO NOT WAIT TOO LONG BEFORE HAVING IT SEEN ABOUT,CAUSING POSSIBLY A BIG REPAIR BILL, INSTEAD OF A SMALL ONE

2010 Ford Fusion... | Answered on Aug 16, 2014


Have to perform some testing to find vehicle problems

What OBD Codes do you have?

Have you Googled your codes ?

2010 Ford Fusion... | Answered on Jul 31, 2014


Data Base at repair shop or at a dealer

2010 Ford Fusion... | Answered on Jul 30, 2014


Could be a few things. End link bushings, struts, cv axles, tie rods, or ball joints. A suspension component for sure.

2010 Ford Fusion... | Answered on Jul 22, 2014


Mechanic is locked in the trunk tapping to get out.
OK is the tapping when turning the key, if so battery is to low to turn over the engine, many things can cause a dead battery. 1) bad alternator if bad your car is a power wheel and the battery will need a charge every time you drive a long distance. the battery is made to start the car once started the alternator runs the car and charges the battery. Crude alternator test, jump car to start once running pull pos. battery cable if car keeps running alternator is OK DO NOT RECONNECT CABLE, TURN OFF CAR FIRST 2) any equipment left on while car sits drawing power like stereo amps etc. 3) corroded and loose cables on the battery (clean and lube)

2010 Ford Fusion... | Answered on Jul 19, 2014


have a compression test done to confirm your suspicions. If the compression is low on some but better on others it may be valves . If the compression doesn't alter check the cam shaft is turning ( broken timing belt)

2010 Ford Fusion... | Answered on Mar 24, 2014

Not finding what you are looking for?
2010 Ford Fusion 2.5 Logo

90 questions posted

Ask a Question

Usually answered in minutes!

Popular Products

Top Ford Experts

Marvin
Marvin

Level 3 Expert

85239 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

gerry bissi

Level 3 Expert

4388 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Fusion Ford

  • Fusion Ford

Most Popular Question

chain oil pan 2010 ford fusion 2 5

  • Cars & Trucks
Loading...