2011 Citroen C3 Picasso - Answered Questions & Fixed issues
How do I set clock on c3 picasso
Press the "MENU" button for access to the main menu , then press the " ^ " or " v " buttons to scroll through the various menus: - radio-CD, - vehicle conf guration, - options, - display settings, - language, - units. Press the "OK" button to select the menu required.
Once the "Display settings" menu has been selected, you can gain access to the following settings: - year, - month, - day, - hour, - minutes, - 12 or 24 hour mode.
Once you have selected a setting, press the " << " or " >> " buttons to change its value. Press the " ^ " or " v " buttons to switch respectively to the previous or next setting. Press the "OK" button to record the change and return to the normal display.
How do i wire my c3 picasso to run my caravan fridge
easy fit a relay under the bonnet thats energised when the ignition is turned on,then run the feed with a thick cable to aux tow plug on the tow bar ,and if you want to be really clever use a dash mounted light to show the power is on and maybe even a master switch as well on the dash controlling the relay with a built in light in the switch .The relay picking up its feed from the ignition switch as sometimes the relay contacts can arc across so it doesnt turn off causing a flat battery .You name i wear the tea shirt for this.Another way is a inverter so the cable to the fridge can be a thinner cable again tea shirt for this as well then getting a belt in the rain when disconnecting the plug but it does work better on 250 volts AC
Citroen c3 2006 anti-theft
I had the same problem.when I used my main key my car wouldn't start and I got the message "anti theft
faulty". The key and the remote still unlocks and locks the doors and turns the lights
on/off but it just wouldn't start my car. I was able to start my C3 by using the spare key. The main key is still faulty and if used brings up the same message.
Were is the horn located on my 2017 citroen dispatch
The most likely location for it is up under the front, left wing between the front wheel and the bumper. You might need to take the wheel arch liner out to get to it. If it's not there check the wheel arch on the other side. Another common location is behind the front bumper mounted on the bodywork crossbar between the radiator and the front grille.
Citroen Relay van 2011 doors will not open
These locks don't work like traditional mechanical locks. It's just spinning as the lock and key are designed to do it if a wrong key is used. Original keys can become too worn to engage the mechanism inside it making it spin the same way. Try these basics.
Do you have a spare key you could try? Is there a key slot in the passenger side door you could try? Could you get to the driver's seat through the side or rear doors? Have you tried spraying a fine oil into the lock to lubricate it.
*NOTE* Do NOT use WD40 as it is not an oil. I would suggest something like GT85 or 3in1 spray.
How to replace plus wire on Citroen c8 diesel?
Disconnect your battery!
Remove the old wite from the battery supply end to the far end.
Replace it in the reverse order connecting the battery supply end last.
Reconnect your battery.
How do i remove control panel on a citroen c4 2016
To remove the control panel on a Citroen C4 2016, you'll need to follow a series of steps. Please note that working on the electrical components of a vehicle can be complex, and it's important to exercise caution and disconnect the car's battery before attempting any removal. It's recommended to consult the vehicle's service manual or seek professional assistance if you're not familiar with car electronics. Here's a general guideline:
1. Disconnect the Battery:
Before working on any electrical components, disconnect the car's battery to prevent any accidental electrical shorts.
2. Remove the Trim Panels:
The control panel is typically located behind the dashboard trim panels. To access it, you'll need to remove these panels. Carefully use a panel removal tool or a flat-head screwdriver to pry off the trim panel. Be gentle to avoid damaging the clips or the panel itself.
3. Unclip the Control Panel:
Once you have access to the control panel, you'll need to unclip it from the dashboard. The control panel may be held in place by clips, screws, or a combination of both. Carefully remove any screws or clips holding it in place.
4. Disconnect Wiring Harness:
After unclipping the control panel, there will be a wiring harness connected to it. Carefully disconnect the wiring harness by pressing down on any locking tabs and pulling it out. Be cautious while doing this, as improper handling may damage the wiring or connectors.
5. Remove the Control Panel:
With the trim panel removed and the wiring disconnected, you should now be able to remove the control panel from its mounting location. Gently slide it out.
6. Installation:
To reinstall the control panel, follow the steps in reverse order. Reconnect the wiring harness, secure the control panel in its mounting location, and reattach the trim panels.
7. Reconnect the Battery:
Once you've completed the installation, reconnect the car's battery.
8. Test:
Not finding what you are looking for?