2015 Land Rover Range Rover Sport - Page 2 - Answered Questions & Fixed issues

Dirty sensors?

Hello my range rover sport tailgate glass won't open so can anyone give me advice how to fix it and tell me what the problem is exactly if it is a fuse or something. Can you please text me on 07455527235 to tell me how to fix it or what the problem is. Thanks Shayaan

odds are it just needs to dry out...many vehicles when thoroughly wet will display a rough idle or stall. while at the car wash its possible several electrical components got wet causing electrical current to stray from its desired path leading to loss of power to vital components...if this is the case the moisture that caused this problem should evaporate with time

Need more info.,year,make,model and engine size.

Timeing belt is broke, Probaly,

The 2004 model is behind the glove box.

Your door jam switch is in the area where the door hinges are connector and can be higher or lower in that cavity.Most likely it is in the Drivers door or the passengers as they are the 2 most used doors. But sometimes the Manufacturers will include the rear cargo lid as a "door"The switches may be gently undone like any bolt. The correct word would be censored out on this site so I must say bolt. There are usually 3 wires in each doorjam pin. You may also notice that if you have "air suspension" that the vehicle is not adjusting the suspension.TAPE is a must before you start removing these doorjam pins. You do not want the wire harness slipping inside the doorjams. If you have any wires, tape them to prevent this problem.If you have not found the problem, some wiring diagrams can be obtained from Autozone.com by registering your vehicle. Another site is alldatadiy.com.I hope my solution is helpful.

Please check this link for tips if your car battery is draining overnight.
click this link:

http://www.fixya.com/cars/r5824824-draining_car_battery_charge

probably worn out bushings

Turn on the ignition whilst holding to talking head button in the centre console and hold for about 6 seconds....make sure the Bluetooth is on and you should get the phone activation message on the car when the button is released.....type in the passkey into your phone and all should work.----------- Be careful with turning the ignition on - it must be only to position 1, not to position 2 and back again - its quite sensitive to this, start again if you go to position 2 by mistake. It may also help if you completely clear the memory of all other connected phones from the car - to do this you have to get into "pairing mode" by going to igntion pos 1 and pressing the talking head button for 10 secs, then keep it pressed for another 10 secs till you get a triple beep - then the memory is completely earsed from all prev phones and it may be easier to pair.---------- ------------------- On some cases the iphone4 will not pair with bluetooth, this is due to firmware.------
This is presumably due the iPhone with the firmware update in iOS 4.3 is not recognized by the car's bluetooth system. This can be easily sorted out: First de-authorize your iPhone from your car's telephone system. Then turn on the iphone bluetooth. Update the bluetooth phone in your car. Now the car's bluetooth system will recognize it as a new phone and direct you with the set-up which will include generating a pass-code etc for pairing. After the completion, the iPhone should be able to pair with your car's bluetooth system. ----------- This should help.Keep updated.Thanks.Helpmech.

Sounds like your Mixture needs to be ajusted. To much gas getting to your engine would cause heavy black smoke. I recommend you have someone give it a good tune-up.

Good Luck

You must drain and refill the fuel tank. Some of these systems use optical sesnors in the injection pump and can be damaged not to mention the damage to the pistons and valves. Great trucks. Drain the tank.

Hi, this problem could be contributed to either slipping clutch plate, mis-adjusted throttle position sensor, or even too much slack throttle cable.

Best case scenario is throttle cable that is a wrench to tighten.

Worst case is sensor or slipping plate for either are pricy, unless you consider yourself a mechanic the first is the only one you can fix and if you do consider yourself a mechanic, get a chilton guide for your car and it will show you those two parts and how to fix the sensor could possibly be an easy fix(coming from me who rebuilds engines). But the plates slip would be a two day long project with specialized tools. so...

Check the cable and if not that take it to mechanic.

Unplug your battery for a minute or two and then hook it back up. If they come back on, you might need a computer to clear them.

I'd have either the dealer or Rover specialty shop set it for you. To set the timing you need Rover "textbook" software, laptop and special wiring. (I have a Rover also) The software is about $2k
Depending on what gasket(s) were changed, timing shouldn't have changed. More than likely an injector line or ignition wiring is wrong. In either case I would let a specialist look at it instead of throwing parts at it.

you have to; go to the authorized dealer for it

Hello! This problem is well known by dealerships...A solution is to have the transmission software updated...This is not a 100% cure...The Control valve body may need to be replaced...Take the vehicle to an authorized dealer and have a diagnostic run on the transmission...They are aware of the fault...


Guru....saailer I’m happy to help further over the phone at https://www.6ya.com/expert/david_6df67de3b14de867