2011 Ford F-350 Super Duty - Answered Questions & Fixed issues

It has to be scanned. System checks don't give you all the info you need.

2011 Ford F-350... | Answered on May 08, 2016 | 68 views

The pump is on the bottom of the washer fluid container. Take out the bottle and remove the pump.

2011 Ford F-350... | Answered on Mar 12, 2016 | 355 views

The radio is a completely differant curcuit. So if the lights make radio go out, There has to be a short or bad wire in the headlight curcuit. Check headlight grounds and clean them good if bad. Good-Day!

2011 Ford F-350... | Answered on Nov 16, 2014 | 40 views

suspect a loose wire to a speaker/s check that all wires are connected tight.

2011 Ford F-350... | Answered on Dec 13, 2013 | 136 views

Hopefully your warrantee is still good,
or you install a new blower motor

2011 Ford F-350... | Answered on Mar 02, 2013 | 96 views

do a generic obd2 test it will show what codes are set / if light is allways on ti is a hard code
the vehicle is more than likely in default

2011 Ford F-350... | Answered on Jan 07, 2011 | 255 views

The process is simple but too lengthy to post here.

Goto homelink.com

They make the system and have very complete instructions you can download.

PLEASE NOTE: MOST but not ALL Brands / models of opener will work with this system.

2011 Ford F-350... | Answered on Nov 28, 2010 | 608 views

I have replaced one in my ford exp. It was easy but mine was toward front of engine and easy to get to. I am not sure where #10 is on your 350.

Ford F-350 Super... | Answered on Apr 11, 2014 | 41 views

Google the question & read up on it

Go to You Tube Video & watch

All your questions are on the internet

Won't be easy, unless you have to experience &
touch of a machinist

Look at the tool required on the net & see how it is used

Ford F-350 Super... | Answered on Apr 11, 2014 | 48 views

Mr. Harris, My advise is to drain the water and fuel mixture from your fuel tank,remove if is easy the fuel tank and completely dry it up,Go by the engine bay and find the fuel pipe which is coming from the tank to the injection system where probably is a fuel filter,renew the fuel filter, blow air in the pipe from the engine side towards the fuel tank-but before you do blow air in the pipe be sure is not connected to the fuel tank,for not sending the water back in. If you did not start the car since water went into fuel,means that you finished with the above,by connecting everything and put fuel in the tank and start the engine. If you did have the engine running when water went into fuel,means that you have to remove the spark plugs and whilst are out and the fuel tank is clean with new fuel and fuel filter make the engine spinning second to second for 2-3 minutes so as the any old fuel to push out from the spark plug holes. After clean your spark plugs or renew them and also before running the engine is good to put an injection cleaner additive in the fuel tank. Better to put fuel up to a quarter of the tank and run it treating all the system.

Ford F-350 Super... | Answered on Apr 03, 2014 | 166 views

My initial thought is Aluminum can be welded. Depends on cracks relationship to mounting bolts. Check and see if Bell housing is separate from transmission. May be able to swap bell housings and keep transmission.

You may want a good Salvage yard site like Carparts.com. They have a Nationwide link to many Salvagers. One request and you could get 300 responses.

Ford F-350 Super... | Answered on Mar 29, 2014 | 87 views

Something seriously loose or worn:

- steering box mounts
- steering column universal joint or end clamp
- steering box inner ball joints
- tie rod ends
- outer ball joints
- wheel centre hub nut
- wheel stud nuts

A simple test is to jack up both front wheels and place the vehicle on axle stands. Then have someone hold the steering wheel, grab a front wheel at the 9-and-3 o'clock position, and shake it hard in and out. If you can feel slack or looseness, or the person holding the steering wheel can, you have a dangerous fault which should be fixed ASAP.

Ford F-350 Super... | Answered on Mar 26, 2014 | 173 views

Might well be a cam sensor. Located on the front of the engine it is held in by one cap screw and is easy to replace. Most of those were recalled and replaced by Ford but they do go bad from time to time.

Ford F-350 Super... | Answered on Dec 18, 2013 | 42 views

just because the rotors are new dosen't mean they come out of the box 100%,you might have one that is running out,causing the pulse,most pften it is recommended to have them turned on a brake lathe prior installation (saves you the trouble of doing the job twice)

Ford F-350 Super... | Answered on Feb 09, 2013 | 1,132 views

The following are the general instructions on the start of diagnosing any electronically controlled engine or transmission problem.

The engine and the automatic transmission (transmission control is only for automatics, engine is still computer controlled no matter the transmission type) in this vehicle are computer controlled and in most cases when a fault occurs a fault code is stored in the memory of the computer control module. There are exception to this, such as the Mass Airflow Meter and fuel pressure problems. What must be done is to have all the basic testing done such as a scan of the system for fault codes as well as a check with a live data scanner tool for engine functions that are not within range of normal, a trained technician is required to know what is correct and what isn't, then based on careful diagnostics done from a factory repair manual the correct part is replaced or the wiring repaired or the computer replaced (known as the PCM or ECM,ECU), which is very rarely the problem. Other basic checks must be done as well such as mechanical problems with the engine as well as engine state of tune and mileage on the engine. The transmission can have mechanical issues as well such as no gear engagement at all or a failed pump or other pressure related problems. Also engine mechanical problems can and do cause many drive-ability related problem such as rough idle and other symptoms.

Ford F-350 Super... | Answered on Dec 20, 2012 | 193 views

I would suggest that this noise is the exhaust cooling down it gets up to 1000F when running and that hot of metal makes noise as it contracts and cools.

Ford F-350 Super... | Answered on Sep 07, 2012 | 49 views

No idea maybe DJtech can help on this one as us poor euroepon relatives here in europe couldnt hope to afford the fuel to put in this beast let alone have this sort of info although i have done one of these a few months ago for a millionare but the tight so and so had a gas conversion on it then hid a couple of domestic gas bottles in the back to run it on well hidden they were as this would result in the vehicle being impounded by customs in any EEC country as their is no tax on a domestic gas bottles ,now you know how the rich get richer by being gigger thieves and schemers than the rest of us and use a fancy brief to get them off the hook if and when they do get caught

Ford F-350 Super... | Answered on Jun 06, 2012 | 424 views

use a good micro spft towel

Ford F-350 Super... | Answered on May 27, 2012 | 151 views

Not finding what you are looking for?
2011 Ford F-350 Super Duty Logo

55 questions posted

Ask a Question

Usually answered in minutes!

Top Ford Experts


Level 3 Expert

85239 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14852 Answers


Level 3 Expert

4372 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides