20 Most Recent 2011 Chevrolet HHR - Page 4 Questions & Answers


recheck the timing,valve clearance, run the OBD for any codes to faulty sensors etc

Chevrolet HHR... | Answered on Jan 19, 2019


Hello Kenneth...a simple one wire toggle switch will do the trick...the ignition switch pink wire will interrupt the start/crank function but your anti theft system may not like the power disruption during ignition off mode. Always make sure your battery is disconnected while making modifications and carefully research the effects of electrical mods. You can always remove a related fuse ie: (fuel pump) if you are trying to secure the vehicle from another ignition key.

Chevrolet HHR... | Answered on Jan 05, 2019


look in the glove box for the code or the trunk. you might find it there. if not, then copy your vin # down and call the dealer for the code.

Chevrolet HHR... | Answered on Dec 24, 2018


Shud tell u on the cover or a partplace will showu

Chevrolet HHR... | Answered on Dec 16, 2018


spray some throttle body into the throttle body to clean it out. Do this by taking off the air filter tubes. Start the engine and slowly spray into the throttle body.

Chevrolet HHR... | Answered on Dec 04, 2018


Has electronic power steering ,no steering fluid .

The electric power steering (EPS) system reduces the amount of effort needed to steer the vehicle. The system uses the body control module (BCM), power steering control module (PSCM), torque sensor, discrete battery voltage supply circuit, EPS motor, serial data bus, and the instrument panel cluster (IPC) message center to perform the system functions. The PSCM, torque sensor, not the EPS motor are serviced separately from each other or from the steering column. Any EPS components diagnosed to be malfunctioning requires replacement of the steering column assembly, also known as the EPS assembly.

Your best bet , take it to a qualified repair shop.

Chevrolet HHR... | Answered on Oct 15, 2018


Eyes, but you will have to jack it up and reach from below. Be careful and do not burn yourself on the exhaust.

Chevrolet HHR... | Answered on Sep 16, 2018


Have tried locking and unlocking the car door with the key?

Chevrolet HHR... | Answered on Aug 13, 2018


run the fault codes
fix the sensor problem
reset using a scan tool

Chevrolet HHR... | Answered on Jul 14, 2018


The best solution you'll get from books at www.reliable-store.com

  1. These are books containing info on repair, service, troubleshooting, parts info, assembling dissemble, removal, error/fault codes, wiring diagrams and everything on any vehicles cars, atv, trucks. forklifts, boats, excavators etc

Chevrolet HHR... | Answered on Jun 19, 2018


Do you know how to test electrical circuit's using a wiring diagram an a voltmeter ? Reading how the headlamps are suppose to work ,then testing is how to find the problem .
Headlamps
The headlamps may be turned ON 2 different ways. First, when the driver places the headlamp switch in the HEADLAMP position, for normal operation. Second, with the headlamp switch placed in the AUTO position, for automatic lamp control (ALC). During ALC, the headlamps will be OFF in daylight conditions, or low beam operation in low light conditions. Battery positive voltage is supplied to the low beam relay and the high beam relay in the underhood fuse block. When low beam headlamps are requested, the body control module (BCM) supplies ground to the coil side of the low beam relay. This activates the relay and the relay supplies voltage to the left hand low beam headlamp through the LH LOW BEAM fuse and to the right hand low beam headlamp through the RH LOW BEAM fuse. Ground for the left hand low beam headlamp is provided at G101. Ground for the right hand low beam headlamp is provided at G102. When high beam headlamps are requested, the BCM supplies ground to the coil side of the high beam relay. This activates the relay and the relay supplies voltage to the left hand high beam headlamp through the LH HIGH BEAM fuse and to the right hand high beam headlamp through the RH HIGH BEAM fuse. Ground for the left hand high beam headlamp is provided at G101. Ground for the right hand high beam headlamp is provided at G102.

Free wiring diagrams here http://www.bbbind.com/free-tsb Enter vehicle info. Year , make , model an engine . Under system click on lighting , then under subsystem click on headlamps . Click the search button ,then the blue link .

Video's on youtube on electrical testing

Chevrolet HHR... | Answered on Jun 17, 2018


its possible but low fluid usually would cause all gears to shift late or not timely. I doubt its the fluid but keep it up to specs before convicting the trans clutches. Have u been maintaining it (flush & filter chg on trans)

Chevrolet HHR... | Answered on May 12, 2018


Metric socket set. Extensions. Ratchet. Hose clamp removal pliers. Transmission line disconnect tool.

Chevrolet HHR... | Answered on Dec 04, 2017


Pretty hard to do without flush equipment because the heater hoses are metal. Can't tap into them easily.

Chevrolet HHR... | Answered on Dec 04, 2017


What engine?

If you need further help, I’m available over the phone at https://www.6ya.com/expert/david_4c166ba81493f541

Chevrolet HHR... | Answered on Nov 07, 2017


89 inch puonds

If you need further help, I’m available over the phone at https://www.6ya.com/expert/david_4c166ba81493f541

Chevrolet HHR... | Answered on Nov 07, 2017

Not finding what you are looking for?
2011 Chevrolet HHR Logo

89 questions posted

Ask a Question

Usually answered in minutes!

Popular Products

Top Chevrolet Experts

Marvin
Marvin

Level 3 Expert

85239 Answers

john h

Level 3 Expert

23515 Answers

Joe Taylor
Joe Taylor

Level 3 Expert

2228 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

HHR Chevrolet

  • HHR Chevrolet

Most Popular Question

2011 chevrolet hhr 2 2 t le8 p0016 p0017

  • Cars & Trucks
Loading...