2004 Ford F-350 Super Duty - Answered Questions & Fixed issues


Good question! Have you been using any odd biofuel? this is probably the first thing Ford will ask you .In 40 years of fixing cars, I never had this problem.

2004 Ford F-350... | Answered on Mar 07, 2015 | 66 views


You can find the code as it is printed on a sticker on the control box.
It will be up under the center part of the dash, about where the transmission tunnel meets the firewall. You have to reach up in there and pull back the carpet and insulation to find the box which has the 5 digit code printed on it.

2004 Ford F-350... | Answered on Feb 25, 2015 | 29 views


It is in the Auxiliary relay box #1 driver side under the hood
middle of the fender .

2004 Ford F-350... | Answered on Jan 26, 2015 | 426 views


12 volt test light or amp gauge. Trailer brakes use 2 wires... 1 ground and 1 hot. The hot has varied amps to apply according to the controller. 12 volt test light works great. use the white (typical) as your ground and the blue (typical) as your hot. Apply brakes. Light should get brighter as the controller is turned up and dimmer as it is turned down. I hope this helps.

2004 Ford F-350... | Answered on Jun 27, 2014 | 97 views


are the brakes on the trailer stuck on , even partially , is the trailer too heavy for the vehicle ? if all this ok i'd check the water pump is ok on your truck, as the extra power needed for towing , will put extra strain on all ancirally components , ie drive belts , water pump , alternator, keep me posted if you wish

2004 Ford F-350... | Answered on Jun 11, 2014 | 63 views


Check to make sure the bulb sockets are tight and free of corrosion. Moisture will often get inside. If this is not the culprit, grab a multimeter and make sure you have a good ground.

2004 Ford F-350... | Answered on Mar 28, 2014 | 128 views


I have replaced one in my ford exp. It was easy but mine was toward front of engine and easy to get to. I am not sure where #10 is on your 350.

Ford F-350 Super... | Answered on Apr 11, 2014 | 40 views


Google the question & read up on it

Go to You Tube Video & watch

All your questions are on the internet

Won't be easy, unless you have to experience &
touch of a machinist

Look at the tool required on the net & see how it is used

Ford F-350 Super... | Answered on Apr 11, 2014 | 47 views


Mr. Harris, My advise is to drain the water and fuel mixture from your fuel tank,remove if is easy the fuel tank and completely dry it up,Go by the engine bay and find the fuel pipe which is coming from the tank to the injection system where probably is a fuel filter,renew the fuel filter, blow air in the pipe from the engine side towards the fuel tank-but before you do blow air in the pipe be sure is not connected to the fuel tank,for not sending the water back in. If you did not start the car since water went into fuel,means that you finished with the above,by connecting everything and put fuel in the tank and start the engine. If you did have the engine running when water went into fuel,means that you have to remove the spark plugs and whilst are out and the fuel tank is clean with new fuel and fuel filter make the engine spinning second to second for 2-3 minutes so as the any old fuel to push out from the spark plug holes. After clean your spark plugs or renew them and also before running the engine is good to put an injection cleaner additive in the fuel tank. Better to put fuel up to a quarter of the tank and run it treating all the system.

Ford F-350 Super... | Answered on Apr 03, 2014 | 165 views


My initial thought is Aluminum can be welded. Depends on cracks relationship to mounting bolts. Check and see if Bell housing is separate from transmission. May be able to swap bell housings and keep transmission.

You may want a good Salvage yard site like Carparts.com. They have a Nationwide link to many Salvagers. One request and you could get 300 responses.

Ford F-350 Super... | Answered on Mar 29, 2014 | 86 views


Something seriously loose or worn:

- steering box mounts
- steering column universal joint or end clamp
- steering box inner ball joints
- tie rod ends
- outer ball joints
- wheel centre hub nut
- wheel stud nuts

A simple test is to jack up both front wheels and place the vehicle on axle stands. Then have someone hold the steering wheel, grab a front wheel at the 9-and-3 o'clock position, and shake it hard in and out. If you can feel slack or looseness, or the person holding the steering wheel can, you have a dangerous fault which should be fixed ASAP.

Ford F-350 Super... | Answered on Mar 26, 2014 | 172 views


Might well be a cam sensor. Located on the front of the engine it is held in by one cap screw and is easy to replace. Most of those were recalled and replaced by Ford but they do go bad from time to time.

Ford F-350 Super... | Answered on Dec 18, 2013 | 42 views


just because the rotors are new dosen't mean they come out of the box 100%,you might have one that is running out,causing the pulse,most pften it is recommended to have them turned on a brake lathe prior installation (saves you the trouble of doing the job twice)

Ford F-350 Super... | Answered on Feb 09, 2013 | 1,119 views


The following are the general instructions on the start of diagnosing any electronically controlled engine or transmission problem.

The engine and the automatic transmission (transmission control is only for automatics, engine is still computer controlled no matter the transmission type) in this vehicle are computer controlled and in most cases when a fault occurs a fault code is stored in the memory of the computer control module. There are exception to this, such as the Mass Airflow Meter and fuel pressure problems. What must be done is to have all the basic testing done such as a scan of the system for fault codes as well as a check with a live data scanner tool for engine functions that are not within range of normal, a trained technician is required to know what is correct and what isn't, then based on careful diagnostics done from a factory repair manual the correct part is replaced or the wiring repaired or the computer replaced (known as the PCM or ECM,ECU), which is very rarely the problem. Other basic checks must be done as well such as mechanical problems with the engine as well as engine state of tune and mileage on the engine. The transmission can have mechanical issues as well such as no gear engagement at all or a failed pump or other pressure related problems. Also engine mechanical problems can and do cause many drive-ability related problem such as rough idle and other symptoms.

Ford F-350 Super... | Answered on Dec 20, 2012 | 191 views


I would suggest that this noise is the exhaust cooling down it gets up to 1000F when running and that hot of metal makes noise as it contracts and cools.

Ford F-350 Super... | Answered on Sep 07, 2012 | 49 views


No idea maybe DJtech can help on this one as us poor euroepon relatives here in europe couldnt hope to afford the fuel to put in this beast let alone have this sort of info although i have done one of these a few months ago for a millionare but the tight so and so had a gas conversion on it then hid a couple of domestic gas bottles in the back to run it on well hidden they were as this would result in the vehicle being impounded by customs in any EEC country as their is no tax on a domestic gas bottles ,now you know how the rich get richer by being gigger thieves and schemers than the rest of us and use a fancy brief to get them off the hook if and when they do get caught

Ford F-350 Super... | Answered on Jun 06, 2012 | 423 views


use a good micro spft towel

Ford F-350 Super... | Answered on May 27, 2012 | 150 views

Not finding what you are looking for?
2004 Ford F-350 Super Duty Logo

Popular Tags

37 questions posted

Ask a Question

Usually answered in minutes!

Top Ford Experts

Marvin
Marvin

Level 3 Expert

85239 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14850 Answers

Mike

Level 3 Expert

4369 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...