2004 GMC Sierra 2500HD - Answered Questions & Fixed issues
GMC 2500HD tie rod end
Here are the tie rod end nut torque specs:
• Lower Control Arms - (Front and Rear bolt) 129 ft-lbs x2 and (Knuckle Stud) 37 ft-lbs
• Upper Control Arms - (Front and Rear bolt) 140 ft-lbs x2 and (Knuckle Stud) 37 ft-lbs
• Inner Tie Rods - 81 ft-lbs
• Outer Tie Rods - (Knuckle Stud) Tie Rod nut 44 ft-lbs and jam nut 55 ft-lbs
• Stabilizer Links - 17 ft-lbs
• Rear Shocks - Lower and Upper 85 ft-lbs
• Front Shocks - Module Bolt x2 37 ft-lbs, Module nut x3 37 ft-lbs and Stud nut 37 ft-lbs
6/28/2020 11:38:06 AM •
GMC Sierra...
•
Answered
on Jun 28, 2020
•
13,216 views
2011 GMC Sierra 2500hd diesel. When I put it in drive, the idle goes up 200 rpm.
The best solution you'll get from books at
www.reliable-store.com
These are books containing info on repair, service, troubleshooting, parts info, assembling dissemble, removal, error/fault codes, wiring diagrams and everything on any vehicles cars, atv, trucks. for klifts, boats, excavators etc
6/21/2018 4:21:10 PM •
GMC Sierra...
•
Answered
on Jun 21, 2018
•
60 views
Air bag light
you need to have the airbag serviced! Sounds like a short circuit
12/10/2017 6:42:26 PM •
GMC Sierra...
•
Answered
on Dec 10, 2017
•
68 views
2005 GMC Duramax, won't restart
Make sure the old filters rubber seal didnt stick to the filter housing when you removed it. While you have the filter off clean up the housing to filter seal. Ut some engine oil on the filter rubber seal befre putting it back on. Costs nothing and just takes a half hour of your time.
8/19/2017 1:51:42 PM •
GMC Sierra...
•
Answered
on Aug 19, 2017
•
174 views
Engine cutting out at high
I need model year and engine size?
How long since a tune-up? Any applicable trouble codes?
I can only help with testing, what testing have you done? Did you use a gage and check proper fuel pressure? Some of the national brand auto stores will check codes for free, if there are any? Do you have drive by wire throttle? Does the speedometer work ok? Sometimes the vss can effect shift points? I'm not telling you to replace anything, but, do some testing. I can't go by what the mechanic did or didn't do. I can't go by what they said.
8/12/2017 6:49:04 PM •
GMC Sierra...
•
Answered
on Aug 12, 2017
•
147 views
Gmc sierra electrical
You might look for a loose or corroded ground. Any problems with the horn or wiper wash motor? I assumed a 5.0L engine. Info I see says there is a ground splice point and a couple of common grounds. If those systems are affected, it would be even more likely. Check fuses as well.
5/17/2017 2:59:24 AM •
GMC Sierra...
•
Answered
on May 17, 2017
•
58 views
Why is Allison transmission banging hard into gear?
Probably a bad solenoid inside the pan if you bring it to a shop and have them scan the tcm the computer should tell you the problem unfortunately the service engine light won't turn on with a tranny trouble code unless it is a major failure that puts a bind on the motor
5/12/2016 5:21:40 AM •
GMC Sierra...
•
Answered
on May 12, 2016
•
516 views
Reset dash lights
I got some subs hookes up in my 2012 dodge avenger and now all my dash lights are on and my lock key will not let me unlock or lock doors what is wrong
8/17/2014 2:57:27 AM •
GMC Sierra...
•
Answered
on Aug 17, 2014
•
163 views
Need 12v switched power source in the dash.
best thing to do, as i presume you want a completely new power feed , run a power and earth cable to the battery and connect the power to the positive pole and place a fuse inline at that point and connect the earth wire to the neg pole , leave the fuse out until you have run the cable to where you want it ,this is a much safer way as can't interfere with any other components already fitted keep me updated if you wish
5/23/2014 9:39:29 AM •
GMC Sierra...
•
Answered
on May 23, 2014
•
265 views
Not finding what you are looking for?