2013 Hyundai Elantra - Answered Questions & Fixed issues

Very Possible it is your fuse, the only thing that makes me think otherwise is that your problem is intermittent. When a fuse blows, things stop working they do not work intermittently. If you recently installed a stereo, check the harness for crossed connections or exposed wiring that may be causing a short. When you blow the fuse for the stereo it usually takes out many of the interior electronic accessories such as Interior dash lights, electronics door locks, dome lamps, etc. Check the fuse box likely under the dash, if not in a corner of the engine compartment under the hood and find the diagram for the fuse lay out. Check the fuse for the stereo or interior accessories or for the door locks. problem could be with the wiring for either.

2013 Hyundai... | Answered on Jul 12, 2019 | 55 views

common issue. It either needs to be reflashed from the dealer or replaced.
Sorry for the bad news.

2013 Hyundai... | Answered on Dec 29, 2016 | 56 views

That is the TPMS warning (tire pressure monitor sensor). Check your tire pressure. The light/symbol is actually supposed to look like a flat tire.

2013 Hyundai... | Answered on Jul 29, 2016 | 211 views

most cabin air filters are located behind glove box. some are located under hood. local auto shop may be able to show you in diagram.

2013 Hyundai... | Answered on Jul 12, 2015 | 76 views

Hi they are usually under the center console near park brake lever. Or forward from that under the dash look for a small metal box with yellow cables going in to it. Good Luck

2013 Hyundai... | Answered on Apr 26, 2015 | 88 views

Check for a drivers door over ride lockout switch or it may be on the centre console that locks out the passengers from playing with their controls.

If this is not the problem or cause let us know so others can keep thinkng about a solution for you please.

2013 Hyundai... | Answered on Mar 12, 2015 | 17 views

If you have a second key, try that one. Sometimes 1 key will unlock, 1 key will start. If not it would be the anti theft or security system disabling the ignition module. Which is why it won't even try to turn over.

2013 Hyundai... | Answered on Feb 21, 2015 | 614 views


2013 Hyundai... | Answered on Jul 12, 2014 | 94 views

I just got the same message today...and rarely use the cd player. Was wroking, went to change cd's, then it would not load and gave error 43...anyone?????

Hyundai Elantra... | Answered on Sep 26, 2019 | 1,169 views

Im not sure if your fuse box looks like the screenshot however if it does I would at your own risk turn this switch off and back on as suggested in the other photo.
Again I am not a mechanic, I do however try to give the best advice I can.
Hope this helps.

Hyundai Elantra... | Answered on Sep 12, 2019 | 146 views

Check the fuse and relay related to the AC. Your fan should come on when the AC is turned on. Right now the fan is working only off the engine temp., not the AC.

Hyundai Elantra... | Answered on Jun 12, 2019 | 71 views

Hose is held to suspension strut with c-clip, loosen and retighten union joint while still in clip for ease of undoing. then remove clip holding hose with pliers
Top up reservoir and to avoid fluid loss, Clamp existing rubber hose off above Wheel cylinders callipers. Spread brake pads slightly to clear disc rotor edge then undo callipers from hub - suspend from strut with cord or wire and unscrew old pipe. Immediately replace existing with new hose to callipers. With master cylinder reservoir sealed airtight undo union nut at top of existing rubber hose where clipped to strut. Replace existing lower hose fitting with new hose.Tighten union. replace c clip and bleed brakes at nipple on callipers until all air out of lines.
Job done road test for hard pedal repeat bleeding as necessary.

Hyundai Elantra... | Answered on Jun 03, 2019 | 33 views

you need a good scanner to program it to the car

Hyundai Elantra... | Answered on May 31, 2019 | 37 views

Use a good scan tool which should identify the failing sensor/circuit when the vehicle stalls,so you can do the correct repair.

Hyundai Elantra... | Answered on May 19, 2019 | 204 views

By pass clutch signal by appling +12vdc to A/C clutch directly - check for proper suction side pressure with A/C gauge connected to suction side of compressor - if pressure is low clutch will not be energized do to low pressure cutout switch. Add freon or 134A to bring up suction side pressure. https://www.6ya.com/callphilipforhelp

Hyundai Elantra... | Answered on May 19, 2019 | 32 views

Sounds like the beginning of a bad 02 sensor. If your engine light is on that’s the issue. I could almost guarantee it. Any auto part store will read the ecu codes for free.

Hyundai Elantra... | Answered on May 15, 2019 | 31 views

Not finding what you are looking for?
2013 Hyundai Elantra Logo

28 questions posted

Ask a Question

Usually answered in minutes!

Popular Products

Top Hyundai Experts


Level 3 Expert

85239 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8984 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides