2009 Lexus IS 250 - Answered Questions & Fixed issues


Any ideas to change Japanese language to
English in IS 250 year 2007.

2009 Lexus IS... | Answered on Apr 21, 2019 | 880 views

A bent rim cannot cause your vehicle to vibrate while stopped. What you describe seems more likely to be an engine misfire or possibly a drive train problem.

2009 Lexus IS... | Answered on Apr 21, 2013 | 156 views

under hood driver side , and kick side driver

2009 Lexus IS... | Answered on Aug 17, 2010 | 129 views

check the motors of centeral locking

2009 Lexus IS... | Answered on Aug 01, 2010 | 59 views

While pressing and holding the odometer reset button press the IGN button twice without your foot on the brake. The display will show some dashes and finally 00000.
The service reminder should be reset.
Hope it will help

2009 Lexus IS... | Answered on Apr 06, 2010 | 1,867 views

Inspect - Brakes, Rotors and brake pads.
Replace smart key battery, coolant,oil and filter.
Reset ( Maint Reqd ) light after oil change, if vehicle equipped with light.
Rotate tire's
Road test - While driving vehicle, check for proper operation of engine, transmission, brakes and steering also check for abnormal noise or vibration from any part of the vehicle.

2009 Lexus IS... | Answered on Jan 22, 2010 | 316 views

Most likely a fuse, or a faulty lighter.

2009 Lexus IS... | Answered on Jan 15, 2010 | 1,061 views

Frankly, I would check locally to see if there is a Japanese translator that would do this for you for a small nominal fee. You can check public libraries and courthouses for possible translators. Craigslist is also another good resource. Check local colleges for persons taking Japanese language!

Someone who can translate is willing to do this for a small ($20?) Fee. Good luck!

Lexus IS 250... | Answered on Mar 29, 2019 | 53 views

I got this free Pdf manual from an online store for free and I don't think Ive visited a mechanic or fixya for help for more than 3-4 times out of the all the times I fixed the chipper in these 4 years

Lexus IS 250... | Answered on Jan 30, 2019 | 242 views

ever think that you should check the oil once in awhile . LIKE WEEKLY

Lexus IS 250... | Answered on Aug 25, 2017 | 219 views

have blown speaker some one turn it up to high and blew it replace it and what the volumne

Lexus IS 250... | Answered on Apr 21, 2018 | 783 views

That hard of an impact caused damage to the sensors for the antislip and brake system. Make an insurance claim because this needs to go to a dealer and could be expensive to fix.

Lexus IS 250... | Answered on Apr 18, 2015 | 259 views

Pedal Relearn Procedure
Accerlerator Pedal Released Postion Learning is and operation to learnicon1.png the full released postions of the accerlerator pedal by monitoring the accelerator pedal sensor output signal. It must be performed each time harness connector of accelearator pedal postion sensor or ECM is disconnected.

1. Make Sure the acceleartor Pedal is fully released
2. Turn Ignition switchON and wait at least 2 Seconds.
3. Turn ignition switchOFF and wait at least 10 Seconds
4. Turn Ignition switchON and wait at least 2 seconds.
5. Turn Ignition switchoff and wait at least 10 seconds

Throttle Valve Relearn
Throttle ValveClosed Postion Learningicon1.png is to learn the fully closed postion of the throttle valveby monitoring the throttle position sensor output signal. It must be performed each time harness of
electric throttle control actuator or ECM is disconnect.

1.Make sure accelerator pedal is fully released.
2. Turn ignition ON
3. Turn igntion switch OFF and wait at least 10 seconds. Make sure that the throttle valvemoves during the 10 seconds by confrming the operating sound.
(You can hear the TB sound when you have key on and shifter in first gear and step on the gas. So you know what you listening for.)

Idle Air Volume Relearn Procedure
The Following Condtions Must be met in order for procedure to Work.

Battery Voltage :More than 12.9 volts at idle
Engine Coolant Temp 158-203 degrees Farenhiet
Electric Load Switch OFF i.e Air Condition, headlamps , rear defogger
Steering Wheel: Neutral Postion (Straight Ahead)
PNP Switch: OFF (Park Neutral Switch i.e. Clutch Switch...pretty sure)

3. Start engine and warm it up to operation temperature
4. Turn igniton switch OFF and wait at least 10 seconds
5. Confirm Gas Pedalif fully realeased, then turn igniton switch ON and wait 3 seconds
6. Fully step on and release gas pedal5 time within 5 seconds
8. Wait 7 seconds and fully step on gas and stay on until MIL stops blinking and is steady.
9. Fully release the Gas pedalwithin 3 seconds after the MIL has turned ON steady.
10. Start engine imediatly and let idle. Wait 20 seconds.

Lexus IS 250... | Answered on Sep 24, 2014 | 6,648 views

5 speed or auto transmissoin clutchs are bad or going out

Lexus IS 250... | Answered on Aug 29, 2013 | 50 views

If its a front wheel drive more then likely its the half shaft That's a drive shaft on the rt front

Lexus IS 250... | Answered on Feb 17, 2013 | 578 views

The first thing you want to check for is the brake signal,without this signal it will not crank,this is the easy one make sure you get brake light,the second is to have the starter tested by a direct method,this gives the indication of the health of the starter

Lexus IS 250... | Answered on Mar 23, 2012 | 1,803 views

Indeed it is frustrating (and weird as well). But can you check, you signed out correctly? If you open Google.com, you will see your email address at top right of the page. If not, then change the try changing the browser. These are only to get sign in page. If you are getting sign in page and cannot sign in that means password is wrong. you can try password reset.

Lexus IS 250... | Answered on Jan 02, 2012 | 109 views

Hello and welcome to FixYa!
What fuse was replaced? You may just have a system failure. As a first course of action, I strongly suggest that you remove the positive battery connector and let it sit for at least 5mins. before reconnecting it. This will reset the system and can get it back to it's normal operation.
Hope this helps and thank you for using FixYa! Have a good one!

Lexus IS 250... | Answered on Sep 05, 2011 | 33 views

If your connector has only two wires... A. It may not matter. B. Look at the connector for a different color clip inserted into it. Removing the clip should allow the piece that holds the wires to release, and maybe there is enough wire there for you to see which goes where.

Just remember how it goes together.

A dealer can tell you or simply see if they have a similar model on the lot, and ask to look under the hood.

Lexus IS 250... | Answered on Aug 13, 2011 | 148 views

Not finding what you are looking for?
2009 Lexus IS 250 Logo

35 questions posted

Ask a Question

Usually answered in minutes!

Popular Products

Top Lexus Experts


Level 3 Expert

85239 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8984 Answers

Are you a Lexus Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides