20 Most Recent 2009 Ford Fusion Questions & Answers

Do you have your owners manual, it will tell you wheres it at and how to access it.

2009 Ford Fusion | Answered on Jul 13, 2020

There are 3 fuses that go to the radio. They all located in the fuse panel under the left hand side of the dash. Fuse #22 7.5 amp, fuse#18 20 amp and fuse#12 7.5 amp.

2009 Ford Fusion | Answered on Feb 05, 2020

those are not codes --before using a scanner read all the instructions on proper use -- rescan and the 7eB's are advising that you have a code and to continue to the next screen to get code[s]

2009 Ford Fusion | Answered on Jul 07, 2019

Just give up, try every spot to find the answer and then jus look down by the brake pedal and turn ur head up and u find the fuse panel.

2009 Ford Fusion | Answered on Sep 11, 2018

to get the piston to move on rear callipers you have to screw the piston back into the housing
this because the piston has a screw in the back that is self adjusting every time you pull the handbrake on
there are special tools to do the job
one is like a wide blade screw driver and other hav prongs on a plate liek a tool to remove grinding discs
comment if you were asked to pay for this advice as it should be free to you

2009 Ford Fusion | Answered on Jan 12, 2017


Feb 21, 2013 - WHAT IS A COMPASS ERROR FOR A 2009 FORD FUSION A MESSAGE COMES UP ON MY DASH SAYS COMPASS NO ... SOURCE: I HAVE A2009 FORD FUSION AND IT'S NOT GOING OVER 20 MPH ... Compass data error -- how do i determine my zone-- ... Jan 28, 2010 ' 2007 Ford Edge SEL Plus.

Compass - Ford Fusion Sport - Ford Fusion Forum

Jan 23, 2013 - Compass - posted in Ford Fusion Sport: 2011 Fusion SEL without navigation screen. Following windshield ... I have recalibrated and reset the compassaccording to the manual instructions (several times) but cannot correct the error. Can anyone help? ... picture of where it is: 2009-08-30_051718_2.gif.

2009 Ford Fusion | Answered on May 21, 2016

Jeanette, break switch is above brake pedal arm, safety neutral switch is on transmission, clutch pedal safety switch above clutch pedal arm. Links below have pics.
to show your appreciation press the helpful button and follow me on fixya for more tips and info.

06 ford fusion brake light switch replace

How To Test and Replace the Neutral Safety Swtich Inhibitor Switch P0705

Clutch switch behind clutch pedal Ford Focus Forum Ford Focus ST Forum...

Replace master cylinder clutch Ford Focus Forum Ford Focus ST Forum Ford...

2009 Ford Fusion | Answered on Feb 15, 2016

Could be a number of things from maladjusted air flaps, faulty servo motors, faulty climate control to a partially blocked heater matrix.

More clues are needed. The first step would be to ensure the engine is reaching full operating temperature and the hot coolant is circulating through the heater.

Erratic or intermittent heater operation can be an early sign of head gasket failure. It is easy to jump to false conclusions so I suggest getting some experienced help.

2009 Ford Fusion | Answered on Nov 23, 2015

Are you sure it's not the other way around? Usually when the idle drops and pressure follows and as the idle increases - the pressure does too. Typical behavior - as long as the pressure remains in the "normal" range it should be OK.

2009 Ford Fusion | Answered on Sep 24, 2015

You should have a sealed hub assembly. You change the whole thing as a unit. You need to remove the wheel and brake caliper, rotor, hub nut, and sometimes have to take off the swaybar end link and pop the lower ball joint to separate the lower control arm from the spindle to gain access to the hub bolts on the back side of the spindle to remove the hub assembly.

2009 Ford Fusion | Answered on Aug 14, 2015

Check the EATX fuse. You need codes.

2009 Ford Fusion | Answered on May 25, 2015

I would start by checking all of the fuses in your car. You have one fuse box under your steering wheel and one inside the engine compartment. You could have blown a fuse controlling the computer related to the acceleration or transmission system.

2009 Ford Fusion | Answered on Mar 24, 2015

Make sure master is full, maybe over fill new brake fluid. Find a helper to push on the brake pedal. You loosen the bleed screw (looks a little like a grease fitting with a hole in it) on the back side of the wheel until there is no more air. tighten. Refill Master cylinder. Then other side same process. Do several times. try to collect the "used" brake fluid to prevent a mess. Now do the same for the front to make sure they don't have any air. IF it still is a soft pedal better have reliable brake shop check.

2009 Ford Fusion | Answered on Mar 13, 2015

yes they all do

If you need further help, I’m available over the phone at https://www.6ya.com/expert/mike_9693b5ad75773352

2009 Ford Fusion | Answered on Mar 03, 2015

Not finding what you are looking for?
2009 Ford Fusion Logo

246 questions posted

Ask a Question

Usually answered in minutes!

Popular Products

Top Ford Experts


Level 3 Expert

85239 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14866 Answers


Level 3 Expert

4372 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Fusion Ford

  • Fusion Ford

Most Popular Question

heater blow cold

  • Cars & Trucks