Hyundai Tiburon - Recent Questions, Troubleshooting & Support

Insufficient Information

2003 Hyundai... | Answered on Jan 12, 2020

It is located in driver's side in engine bay. Square box . This cutoff is a safety device to stop the fuel pump on case of impact.

2004 Hyundai... | Answered on Oct 03, 2019

Check with the application catalogue of your choice of oil brand and you should find your car listed with the appropriate grade of synthetic oil.

There is a note of caution, especially with an engine that has already covered a fair mileage. Depending on the service history and the type of oil used in the past, the engine could be clean, slightly dirty or very dirty inside and changing to a high detergent oil if the engine is dirty could cause problems. Detergent oils scour the inside and cleans things and holds the dirt in suspension so it gets drained at the next oil change.
The trouble is, there is a limit to how much dirt the oil can hold and if that limit is reached mass dumping can happen - blocking filters and oilways.

It is a while since I encountered an engine that died of a thrombosis and the additive packs of oils have been improving all the time but the point should be considered...

2006 Hyundai... | Answered on May 05, 2019

You would have to take transmission out and disassemble.......only half part and then use mega silicone gasket


2003 Hyundai... | Answered on Mar 20, 2019

Hi Donna,
The most common problems with an engine that will not start are lack of fuel in the tank, water in the fuel, the fuel pump not working or there is no spark for ignition.
Realistically, if you know little about engines you need help from a mechanic or someone with knowledge. The only quick try you could apply is to turn on the ignition, then thump the fuel tank with a rubber mallet or your fist. If the pump is stuck, this might jar it into action, but you still need a mechanic to repair or replace the pump, as it is inside the fuel tank.
Good luck.

2001 Hyundai... | Answered on Mar 01, 2019

This came directly from my Hyundia service guy:

Unlock the car, get in and close all doors. Turn the ignition key to ACC, press the Unlock button till blinkers flash. That's it. Get out of the car and see if it works.

Good luck.

2003 Hyundai... | Answered on Feb 12, 2019

Measure the voltage going to and coming from the starter solenoid.

Hyundai Motor... | Answered on Feb 01, 2019

the right direction is to have the fault codes read first
they will reveal a code that refers to TR sensor , VSS sensor or TCM
indicates a problem servo/s or solenoids
If the oil has not been changed in the last 60,000miles then that would be a good option to do after the fault codes reading

2001 Hyundai... | Answered on Oct 04, 2018

The reason that your anti-freeze is gelling in your rad is that the mixture of anti-freeze and water is too weak. this could be because of old anti-freeze(same as oil,it deteriorates over time, usually 2 to 5 years), or there could just be too much water added. I would suggest a cooling system flush, and re-fill with a new 50/50 mixture of water and anti-freeze.

2004 Hyundai... | Answered on Sep 29, 2018

Removal & Installation

Specific to:
Hyundai Entourage 2007-2008
  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Disconnect the negative (-) battery terminal.
  3. Remove the crash pad lower panel (A).

    Fig. Remove the crash pad lower panel (A)
  4. Remove the 2 screws (A) and the trip switch connector.
  5. Remove the crash fascia panel (B).

    Fig. Remove the crash fascia panel (B)
  6. Remove the screw with the ignition in the ON position (IG ON) and disconnect the 6P connector.
  7. Remove the ignition switch (A).
  8. Installation is the reverse of removal procedure.

    Fig. Remove the ignition switch (A)
Specific to:
Hyundai Accent 2006-2008
Hyundai Azera 2006-2008
Hyundai Elantra 2006-2008
Hyundai Sonata 2006-2008
Hyundai Tiburon 2006-2008
  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Remove or disconnect the following:

    The negative battery terminalThe crash pad lower panelThe ignition switch after loosening the screw with IG ON and disconnecting the 6P connector
  3. Installation is the reverse of the removal procedure.hope this helps it is off autozone website

2006 Hyundai... | Answered on Jun 29, 2018

If you have the V-6, there are actually 3 converters. One on each engine bank and one after the Y pipe

2003 Hyundai... | Answered on Mar 16, 2018

Oxygen sensors are usually located in the exhaust system. Assuming yours has the V6 engine you have 4 fitted. They are labelled in the attached photo.


2005 Hyundai... | Answered on Mar 15, 2018

Wiring, schematic, electrical diagrams, fuse diag, error codes, torque settings etc are basic contents of these online books they have here on this website I have attached. Must check it out

2004 Hyundai... | Answered on Mar 14, 2018

What is the make and model of your vehicle? You need a wiring schematic to troubleshoot. It's possible there is a fuseable link in the wire itself that is bad.

2001 Hyundai... | Answered on Feb 26, 2018

I presume you have checked oil and all fluid levels.

Hyundai Tiburon... | Answered on Feb 24, 2018

Not finding what you are looking for?

-1,144 questions posted

Ask a Question

Usually answered in minutes!

Popular Products

Top Hyundai Experts


Level 3 Expert

85239 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8984 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Hyundai Cars & Trucks

  • Forum

View Most Popular

  • Hyundai Cars & Trucks