Hyundai Elantra - Answered Questions & Fixed Issues

About L.B signal i fix it with more than 12 avante cars just remove the gage tableau and remove the built under r phars then you will never see this problem again and for more details you can call me any time +962786742552

Hyundai Motor... | Answered on Dec 23, 2019 | 849 views

Bolt pattern? Like which bolts do you tighten in which order? -always tighten opposite bolts sequentially

2012 Hyundai... | Answered on Dec 19, 2019 | 33 views

it depends. we need to know a lot more like:
-oil weight used
-when does it happen (morning,afternoon)
-does it happen when hot or cold
-are you driving it offroad

if you had a shortblock replaced at 8000km that tells me something about YOUR driving habits and how you maintain a vehicle

2011 Hyundai... | Answered on Nov 06, 2019 | 52 views

look for the metal rod the handle is attached to. you should be able to move that back and forth (latching and unlatching), with pliers, if you can reach it

2008 Hyundai... | Answered on Nov 06, 2019 | 64 views

camshafts don't have torque. the answer you really want depends on the question you are asking. you need to clarify:

1- are you asking about torque generated at the CRANKSHAFT?
2- which country are you in? this dictates your engine specs
3- are you asking about the torque applied to the camshaft hold down button?

2011 Hyundai... | Answered on Nov 06, 2019 | 101 views

I just got the same message today...and rarely use the cd player. Was wroking, went to change cd's, then it would not load and gave error 43...anyone?????

Hyundai Elantra... | Answered on Sep 26, 2019 | 1,176 views

Im not sure if your fuse box looks like the screenshot however if it does I would at your own risk turn this switch off and back on as suggested in the other photo.
Again I am not a mechanic, I do however try to give the best advice I can.
Hope this helps.

Hyundai Elantra... | Answered on Sep 12, 2019 | 154 views

LF Speaker (+) GREEN/RED
RF Speaker (+) RED/BLUE
LR Speaker (-) YELLOW/BLUE
RR Speaker (+) GREEN
RR Speaker (-) GREEN/BLUE
Radio Security YES

Hyundai Motor... | Answered on Jul 22, 2019 | 369 views

Remove one of the spark plugs and check to see if it is getting spark. If it is not getting spark then you have a ignition problem.

2003 Hyundai... | Answered on Jul 13, 2019 | 27 views

Very Possible it is your fuse, the only thing that makes me think otherwise is that your problem is intermittent. When a fuse blows, things stop working they do not work intermittently. If you recently installed a stereo, check the harness for crossed connections or exposed wiring that may be causing a short. When you blow the fuse for the stereo it usually takes out many of the interior electronic accessories such as Interior dash lights, electronics door locks, dome lamps, etc. Check the fuse box likely under the dash, if not in a corner of the engine compartment under the hood and find the diagram for the fuse lay out. Check the fuse for the stereo or interior accessories or for the door locks. problem could be with the wiring for either.

2013 Hyundai... | Answered on Jul 12, 2019 | 61 views

The newer models of most cars don't have a dipstick for ATF. They require you to go in to the dealership to check and replace fluids

2011 Hyundai... | Answered on Jul 01, 2019 | 294 views

The chirp comes from the alarm system itself. it may be a electrical short in the alarm system, or a damage in the alarm itself. u need an alarm shop or a good tech. wish I was there.

2014 Hyundai... | Answered on Jun 27, 2019 | 51 views

Check the fuse and relay related to the AC. Your fan should come on when the AC is turned on. Right now the fan is working only off the engine temp., not the AC.

Hyundai Elantra... | Answered on Jun 12, 2019 | 76 views

Make sure the 3 prongs (2 silver & 1 gold) line up to connect properly when you put it back in. I had to pullout the gold outside of where the bulb sits and slightly pull out the 3 in the actual lens to get a good connection. ***This is what makes the turn signal wireless... They have to be aligned and have contact****

Hyundai Motor... | Answered on Jun 06, 2019 | 578 views

Hose is held to suspension strut with c-clip, loosen and retighten union joint while still in clip for ease of undoing. then remove clip holding hose with pliers
Top up reservoir and to avoid fluid loss, Clamp existing rubber hose off above Wheel cylinders callipers. Spread brake pads slightly to clear disc rotor edge then undo callipers from hub - suspend from strut with cord or wire and unscrew old pipe. Immediately replace existing with new hose to callipers. With master cylinder reservoir sealed airtight undo union nut at top of existing rubber hose where clipped to strut. Replace existing lower hose fitting with new hose.Tighten union. replace c clip and bleed brakes at nipple on callipers until all air out of lines.
Job done road test for hard pedal repeat bleeding as necessary.

Hyundai Elantra... | Answered on Jun 03, 2019 | 34 views

you need a good scanner to program it to the car

Hyundai Elantra... | Answered on May 31, 2019 | 38 views

Not finding what you are looking for?

-3,952 questions posted

Ask a Question

Usually answered in minutes!

Popular Products

Top Hyundai Experts


Level 3 Expert

85239 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8984 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides