Question about ATVs

1 Answer

Back plug not firing on a Kawasaki mule 4010 .2009

Posted by george bowen on

Ad

1 Answer

happy hour

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

  • Contributor
  • 3 Answers
Ad

3 Related Answers

paul4_judith

paul

  • 1190 Answers

SOURCE: front hub removing

remove the wheel then undo the big nut in the center then remove the brake caliper then remove the big nut and the hub will come off !

Posted on May 27, 2014

Ad

Jim

  • 1041 Answers

SOURCE: MY KAWASAKI MULE 3010 WILL GO IN GEAR TO BACK UP BUT NOT FORWARD POPS OR JUMPS OUT OF GEAR

Check shifter linkage / cable adjustment

Posted on Dec 02, 2016

5keepers541

Steve P

  • 3712 Answers

SOURCE: i have a 2006 kawasaki mule trans 4x4 it gets gas spark plugs are firing but will not run

Hey Mike,
An internal combustion engine only needs three things to run...(assuming the internals are all good)..

1. A properly timed spark
2. Correct air/fuel mixture
3. Compression

which of these are you missing??

Posted on Aug 23, 2017

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 2006 kawasaki mule trans 4x4 it gets gas spark plugs are firing but will not run


Hey Mike,
An internal combustion engine only needs three things to run...(assuming the internals are all good)..

1. A properly timed spark
2. Correct air/fuel mixture
3. Compression

which of these are you missing??

Aug 23, 2017 | ATVs

1 Answer

I have a 2003 kawasaki mule model 3000 it wont say running at idle what to do


Full tune up and carb clean .get new plug,air filter.oil Chang ,carb clean and adjustment.that should do it.,., try fuel filters and test fuel pump see if it's functioning properly.,.

Dec 10, 2016 | kawasaki 2005 Mule 3010 4x4

1 Answer

There is no fire to the spark plugs but will turn over what to check


First replace the spark plug with a new one. Then check the wires from the positive terminal on the battery to the coil and then to plugs. Put a 12 volt tester on the positive wires and the battery ground or any metal on the engine to see if circuit is hot. Hope this helps. Make sure you test the plug wire as well.

Sep 21, 2015 | kawasaki 2009 Mule 4010 Trans4x4

1 Answer

Where is the neutral safety switch for a kawaski 3010 mule


Kawasaki Mule Update - YouTube

? 2:16
www.youtube.com/watch?v=Fw_jeQUU6Hw
Jan 25, 2013 - Uploaded by Penguinboy1995
solenoid is reading battery voltage and the constant hot, it is not sending the 12 volts from the switch to the ...

Sep 19, 2015 | kawasaki 2005 Mule 3010 Trans 4x4

1 Answer

Primary clutch bolt for a 2005 Kawasaki 3010 mule 4 x 4 will not screw back in


Hi ! for an informantion, please visit the website below. If you need more information about a specific electrical issue you can reach me at [email protected]
http://www.motorpartstore.com.Good luck and have a nice day.

Apr 12, 2015 | kawasaki 2005 Mule 3010 4x4

1 Answer

What is possible cause that a mule 3010 kaf620e6f will not hold idle?


Air leak .dirty air filter.,.fouled plug.,.bad gas.,.dirty carb?fuel injection? Bad fuel filter ,fuel pump test fuel pump that's the general stuff.go from there

Apr 28, 2014 | kawasaki 2006 Mule 3010 4x4

Not finding what you are looking for?
ATVs Logo

Related Topics:

38 people viewed this question

Ask a Question

Usually answered in minutes!

Top ATVs Experts

john h

Level 3 Expert

23504 Answers

Marvin
Marvin

Level 3 Expert

85239 Answers

ray gallant

Level 3 Expert

70653 Answers

Are you an ATV Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...