Question about kawasaki 2005 Bayou 250

1 Answer

Whst are the valve adjustment for a kawasaki bayou 220

Posted by Christine Chapman on

Ad

1 Answer

Conrad Kruse Jr.

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    New Friend:

    An expert that has 1 follower.

    Cheetah:

    An expert who has answered 20 or more questions within one hour.

  • Expert
  • 189 Answers

What year ? 1999 should be 15 to 20 mm intake on exh 18 to 23 mm i think depending on year. they run tight. adj at tdc on comp stroke with valves open far as they can. have to rotate eng for each valve to open fully and independently one opens and other closes at same time. should be very quiet if adj correctly.adj the closed valve only when fully closed

Posted on Feb 21, 2019

Ad

5 Related Answers

Anonymous

  • 160 Answers

SOURCE: What are the Torque Specs for a Kawasaki Bayou 350 ATV?

which specs do you need engine ?

Posted on Nov 12, 2008

Ad

Anonymous

  • 948 Answers

SOURCE: Just wanted to determine, for a Kawasaki bayou

The valve is open when the lever and valve are parallel. Generally that is down. When the lever is pointing across the valve it is closed. Think T vs. I. If the lever and valve cross it's closed, if they go the same way it's open.

That applies to a two position valve, if your Bayou has a reserve postion it could be different. That would be three positions and across one way would be open, down would be reserve, and across the other way would be closed. Should be marked on the petcock if that is the case.

Posted on Mar 13, 2009

Anonymous

  • 65 Answers

SOURCE: how do i set valves on a bayou 220

remove spark plug rotate motor to top dead center comp. stroke. and adjust valve tappets to. .10mm intake and .15mm exhaust.

Posted on May 02, 2009

Anonymous

  • 1 Answer

SOURCE: no key for our kawasaki bayou 220

On the Bayou 220 you have 2 wires from the Ignition Switch. If I was you I would wire them 2 to a toogle switch or push bottom start.

Posted on Dec 23, 2009

Anonymous

  • 76 Answers

SOURCE: I have a Kawasaki bayou 220, it will only start in

idle jets are clogged needs to have carb cleaned

Posted on Jan 28, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What will cause your 2002 kawasaki bayou 220 not to crank if battery is good?


the solenoid has gone bad most likely. if that checks ok, could be the keyswitch, kill switch or neutral safety switch.

Dec 01, 2017 | kawasaki 2005 Bayou 250

1 Answer

Once the hub is off how do you get the barrens out if they are stuck it's a Kawasaki bayou 220


a large hammer and lots of effort. if the center has come out you can cut the outer ring with a dremel cutting disc.

Nov 20, 2017 | kawasaki 2005 Bayou 250

1 Answer

Kawasaki 220 Bayou has 3 gas lines coming off the carb. Where do they go? I need a diagram


How do you know they are gas lines? Are they the same diameter? Why are they not still connected?
Does this ATV have a fuel pump? If so they probably connect to the pump.. one is the fuel line and one is a vacuum line... the other probably an overflow.

Apr 09, 2017 | kawasaki 2005 Bayou 250

1 Answer

220 bayou well fire but won't start


clean your carb, check for compression.

Feb 25, 2017 | kawasaki 2005 Bayou 250

1 Answer

Do I need a special screwdriver to adjust the carb on a 2006 Kawasaki bayou 250. not idling right after cleaning.


no. idle is a thumb screw on the side of the carb. (I think, mine was an older model)

Nov 12, 2016 | kawasaki 2006 Bayou 250

1 Answer

Why does my '07 Kawasaki Bayou 250 sputter badly at near and full throttle?


clean carburettor there is a clot in it or on fuel line and petrol reserve on off valve.change fuel filter and try it.

Apr 21, 2015 | kawasaki 2007 Bayou 250

1 Answer

How do i adjust my clutch on a kawasaki bayou 220


Maybe time for a clutch rebuild. Loosen nut on right cover, hold in place, run screwdriver slotted bolt in until it seats then back it out 1/2 turn, hold screw in place and tighten the nut!

Jul 06, 2014 | ATVs

1 Answer

How do you line up the timing marks on a 1988 Kawasaki Bayou 220 ??


http://www.mediafire.com/download/j8p6ew6gty8cd44/2003-05+Bayou+250+Service+Manual.pdf#2 for a newer 250 but I think they're all the same

Feb 02, 2014 | kawasaki ATVs

1 Answer

2005 kawasaki bayou 250 4 wheeler carburator problems


do you mean the idle air fuel mix screw adjustment? its 1.5 turns out.

Apr 19, 2013 | kawasaki 2005 Bayou 250

1 Answer

Set timming on 220 bayou kawasaki


T is usually the mark on the flywheel and there's usually a mark on the cam sprocket and head to line up. you can google up a service manual too most likely.

Oct 22, 2017 | kawasaki 2005 Bayou 250

Not finding what you are looking for?
kawasaki 2005 Bayou 250 Logo

Related Topics:

296 people viewed this question

Ask a Question

Usually answered in minutes!

Top kawasaki ATVs Experts

Marvin
Marvin

Level 3 Expert

85239 Answers

gludwick2

Level 2 Expert

60 Answers

Wayne McNeil

Level 2 Expert

209 Answers

Are you a kawasaki ATV Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...