Kymco 2010 MXU 375 IRS 4x4 - Page 4 - Answered Questions & Fixed issues


do you have internet where you live? Try this
"2002 Polaris trailblazer users manual"

ATVs | Answered on Oct 16, 2019 | 192 views


Yea, what you said == just google it.

ATVs | Answered on Oct 16, 2019 | 159 views


Usually, there is a hole plug near the bottom of the casing. BUT first drive it around a lot cause gear oil is heavy and it won't come out very fast if it is cold.

ATVs | Answered on Oct 16, 2019 | 154 views


power to efi module? no, find where it stopped and reconnect.
yes, power out of efi module? no, replace efi module.
yes, open between efi and pump.

ATVs | Answered on Oct 16, 2019 | 206 views


search engine are more efficient. If this isn't to your liking
https://taotao.zendesk.com/hc/en-us/articles/204167645-General-Torque-Spec-Settings-
try searching "clutch nut torque spec"

ATVs | Answered on Oct 16, 2019 | 200 views


I don't understand your problem. What is a "make end"?

ATVs | Answered on Oct 16, 2019 | 129 views


are you into troubleshooting? Probably not, but one must have fuel, ignition, and air to make things burn or run an ICE.
What don't you have?
Is there an ignition source? Did you pull the spark plug and verify it will spark?
Is there fuel? No, not in the tank, it must be getting to the engine.
Is the spark plug wet? If it isn't wet with fuel, you are not getting fuel.
Is there air? No, not what you are breathing, but getting to the carburetor. Did you check the air cleaner?

ATVs | Answered on Oct 16, 2019 | 129 views


It acts like you have burnt spots on the starter shaft that touches the brushes ( voltage) to start. When you rock the vehicle in gear the starter shaft moves and it is placed in a position where the brushes can make a clean contact. Then when you turn the key, the starter will engage and the vehicle will start. My recommendation would be to change out the starter.

ATVs | Answered on Oct 15, 2019 | 178 views


check wire harness for short

ATVs | Answered on Oct 10, 2019 | 150 views


It sounds as though your ignition switch is not hooked up correctly. Follow the harness from the ignition switch to the bullet connectors under the front body plastic. Make sure the colors all match up.

ATVs | Answered on Oct 08, 2019 | 148 views


Even though the overflow is full, the radiator could be empty. You need to remove the radiator cap and make sure it is full to the top. If you find the fluid level is low in the radiator, that would indicate there is a leak in the hose between the radiator and the overflow tank.

ATVs | Answered on Oct 08, 2019 | 151 views


If you bypass unit will not run

ATVs | Answered on Oct 03, 2019 | 166 views


Check rear drive shaft from engine to rear differential.

ATVs | Answered on Oct 03, 2019 | 139 views


Verify spark and fuel.

ATVs | Answered on Oct 03, 2019 | 136 views


Did you check to see if the chokes on?

ATVs | Answered on Oct 02, 2019 | 182 views


Its the oil injection tank. This is the oil that mixes with the gas. Without and oil/gas mixture your 2 stroke motor will be ruined due to lack of internal lubrication. Some people will disconnect them and premix the gas due to a fear of failure of the injection system.

ATVs | Answered on Oct 02, 2019 | 163 views

Not finding what you are looking for?
Kymco 2010 MXU 375 IRS 4x4 Logo

7 questions posted

Ask a Question

Usually answered in minutes!

Top Kymco ATVs Experts

Marvin
Marvin

Level 3 Expert

85239 Answers

john h

Level 3 Expert

23438 Answers

Kardoc

Level 3 Expert

6109 Answers

Are you a Kymco ATV Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...