Shirley Neibarger posted an answer for this Juki Sewing Machines:
"Are you sure it's a 5 thread? I looked at the threading diagram on the 804 and it appeared..."
Shirley Neibarger posted an answer for this Juki Sewing Machines:
"Remove the foot and plate. Take your thread out of the needle and see if you can run the..."
Shirley Neibarger posted an answer for this Juki Sewing Machines:
"Frances, Check to make sure that you don't have a bad needle. If there is a slight burr on..."
Shirley Neibarger posted an answer for this Juki Sewing Machines:
"Generally the machine is making poor stitches going forward before it makes skipped..."
Shirley Neibarger posted an answer for this Bernina Sewing Machines:
"On the right side of your machine, below the hand wheel, there is a small knob. When you..."
Shirley Neibarger posted an answer for this Sewing Machines:
"Your stitch selector knob is still set on the 3rd leg of the buttonhole. Turn your knob..."
Shirley Neibarger posted an answer for this Sewing Machines:
"Generally you have been making buttonholes and have not put the stitch type back onto..."
Shirley Neibarger posted an answer for this Juki Sewing Machines:
"Loosen your top tensions (large tension near the needle, small tension near the top of the..."
Shirley Neibarger posted an answer for this Juki Sewing Machines:
"Oil generally helps. Put a couple drops of oil on screws and let set a while. HOWEVER,..."
Shirley Neibarger posted an answer for this Juki Sewing Machines:
"There is a clear oil gunge cap on top of the machine.It probably is clear and has a small..."
Shirley Neibarger posted an answer for this Juki Sewing Machines:
"Make sure that your bobbin is all the way into the case Make sure that your needle is up..."
Shirley Neibarger posted an answer for this Juki Sewing Machines:
"I am surprised that you have to set the needle bar but put a NEW needle in the bar or make..."
Shirley Neibarger posted an answer for this Juki Sewing Machines:
"It is generally because you have not taken your knee completely off the knee lift...."
Shirley Neibarger posted an answer for this Juki Sewing Machines:
"Check to make sure that your needle is completely inserted up into the machine, and that..."
Shirley Neibarger posted an answer for this Juki Sewing Machines:
"If it is 110 motor, check with your mechanic. If it is 220/3 phase industrial, your poles..."
Shirley Neibarger posted an answer for this Juki America, Inc Juki MO-644D 2/3/4 Thread Overlock Serger JUKI010:
"Check the pulley on your motor. Sometimes thread gets wrapped around the pulley and can..."
Shirley Neibarger posted an answer for this Juki Sewing Machines:
"I am surprised that I couldn't find threading directions in the manuals that I found. It..."
Shirley Neibarger posted an answer for this Juki Sewing Machines:
"Did you get this fixed? Most common problems: 1. You broke a needle and the hole in your..."
Shirley Neibarger posted an answer for this Juki Sewing Machines:
"Did they break or are they scared up? It's not easy to get them right. But try this...."
Shirley Neibarger posted an answer for this Juki Sewing Machines:
"Please send a picture of your machine. I can't find Juki and 932 on line unless you are in..."
Shirley Neibarger posted an answer for this Juki Sewing Machines:
"I am confused as to why one place on this says Juki cp-160 and one says DDL-8500-7 If it..."
Shirley Neibarger posted an answer for this Juki Sewing Machines:
"Have you moved your sewing machine lately? I don't know what model your machine is, but I..."
Shirley Neibarger posted an answer for this Juki Sewing Machines:
"Try a different thread. Did it act ok on that thread? Usually it is because the shuttle is..."
Shirley Neibarger posted an answer for this Juki Sewing Machines:
"Is the motor 110? or 220/3 phase. If the wires are reversed on the motor, it will only run..."
Shirley Neibarger posted an answer for this Juki Sewing Machines:
"See if it is set for buttonhole on the #3 step"
Shirley Neibarger posted an answer for this Juki Sewing Machines:
"Both the motor and the light work off the switch box separately USUALLY. 1. Look under..."
Shirley Neibarger posted an answer for this Juki MO-644 Mechanical Sewing Machine:
"I think the right 'finger' on the plate is out too far. You may need to adjust your..."
Shirley Neibarger posted an answer for this Juki Sewing Machines:
"As a general rule the left cover needs to have its top aligned with the plate and then..."
Shirley Neibarger posted an answer for this Juki Sewing Machines:
"Are you running your thread through the small tension at the upper right of the machine..."
Shirley Neibarger posted an answer for this Juki Sewing Machines:
"Turn it to either extreme and then see if the feed dogs hit the plate when you hand turn..."
Shirley Neibarger posted an answer for this Juki MO-623 Mechanical Sewing Machine:
"DC x 1 should be your needle type. Try this company for your manual: Juki MO-2500 Parts -..."