I am a trained and certified OPE technician.
Matt Olenzek posted an answer for this Honda 2004 FourTrax Foreman ES:
"Yes it is a low oil sensor / switch. It could be faulty, but it can be bypassed by..."
Matt Olenzek posted an answer for this Briggs & Stratton Heavy Machinery:
"The engine drives a pulley, and the chipper / blades run on a shaft supported by sealed..."
Matt Olenzek posted an answer for this Honda 2004 FourTrax Foreman ES:
"Have you tried draining the float bowl and examine for the presence of water?"
Matt Olenzek posted an answer for this Sport & Outdoor - Others:
"Contact Smith and Wesson for a warranty repair."
Matt Olenzek posted an answer for this Sport & Outdoor - Others:
"Do you have a picture of it. Chances are it's a J frame."
Matt Olenzek posted an answer for this Electric Garden:
"Hello, it sounds like you have a loose pot belt. Is the engine running at full speed?"
Matt Olenzek posted an answer for this John Deere Garden:
"Hi this is an informational code, if you call you dealer they can tell you. I'm sorry I..."
Matt Olenzek posted an answer for this John Deere Garden:
"Hi Bill, you electric clutch only engages your pto. The clutch for the Transmission just..."
Matt Olenzek posted an answer for this kawasaki Garden:
"Hey Matt, the valves are timed by the cam gear. The only way this can get out of time is a..."
Matt Olenzek posted an answer for this John Deere Garden:
"If the mower was sitting outside and the ambient temperature is hit during the day and..."
Matt Olenzek posted an answer for this Ironman Exercise & Fitness:
"Hey Joe, at the back of the treadmill, you have the rear roller. The roller has a tension..."
Matt Olenzek posted an answer for this Nordic Track Nordictrack Exp 1000 Treadmill Motor Control Board 13:
"I have tried every recommendation as to how to unlock my Nordic Track 1000 from the..."
Matt Olenzek posted an answer for this Nordic Track Nordictrack Exp 1000 Treadmill Motor Control Board 13:
"Corrine, That knob is spring loaded. You need to pull it out...Hard. Before you do this..."
Matt Olenzek wrote a tip for Nordic Track Exercise & Fitness:
"Make sure you recalibrate your treadmill after installing ANY controller, motor or..."
Matt Olenzek posted an answer for this Electronics - Others:
"i do not have 12 volt power in my 2009 wilderness traveltrailer even when i am hooked up..."
Matt Olenzek posted an answer for this Electronics - Others:
"Scott, Have you checked the circut breakers on the inverter, or the main fuse/breaker..."
Matt Olenzek posted an answer for this Nordic Track Exercise & Fitness:
"need manual"
Matt Olenzek posted an answer for this Nordic Track Exercise & Fitness:
"James, go to iconservice.com and type in your model number and you can download a pdf file..."
Matt Olenzek posted an answer for this John Deere 420,1020,2010,2020,2510,2520 Tractor Float:
"when I turn the key on my JD 2305 tractor to start,it rolls the engine over, but when I..."
Matt Olenzek posted an answer for this John Deere 420,1020,2010,2020,2510,2520 Tractor Float:
"You have a bad relay or pull in timer. You have the same M806808 fuel shut off solinoid as..."
Matt Olenzek posted an answer for this John Deere 420,1020,2010,2020,2510,2520 Tractor Float:
"drive does not work on a john deere 14sb"
Matt Olenzek posted an answer for this John Deere 420,1020,2010,2020,2510,2520 Tractor Float:
"Wow a 14 sb, The best mower John Deere ever built. Hopefully its just the belt. If..."
Matt Olenzek posted an answer for this Craftsman 42 in. Deck 19.5hp Lawn Tractor:
"there is a lot of slack when steering. I would like to know how to tighten it."
Matt Olenzek posted an answer for this Craftsman 42 in. Deck 19.5hp Lawn Tractor:
"Joseph, Most likely it is the bronze bushing at the other end of the steering shaft. You..."