David Spradling posted an answer for this Jandy Pool & Spa:
"if around 7 sec check flame sensor"
David Spradling posted an answer for this Pool & Spa:
"LG is a millivolt heater make sure all contacts are good check across pilot generator on..."
David Spradling posted an answer for this Teledyne Laars Pool & Spa:
"if burner wont stay lit for about 7 sec it is flame sensor not showing rectification clean..."
David Spradling posted an answer for this Jandy Laars Hi - E2 350,000 Btu Heater:
"leak in heat exchange need new one"
David Spradling posted an answer for this Jandy Laars Lite 2 Pool Heater 125,000 Btu / Propane Gas :
"also if no voltage after pressure switch take copper line loose turn system on if no water..."
David Spradling posted an answer for this Teledyne Laars Laars Lx Pool Heater / 400,000 Btu / Propane Gas:
"if your heater is acme (has copper or brass outlets its nickel if standard it is copper..."
David Spradling posted an answer for this Teledyne Laars Laars Lx Pool Heater / 400,000 Btu / Propane Gas:
"check up in the top of heater some come with resetable fusible links reset if possible or..."
David Spradling posted an answer for this Rheem Pool & Spa:
"make sure recirculation pump is working no water flow the switch will not make contact"
David Spradling posted an answer for this Raypak 406A Digital ASME Natural Gas IID Heater009271:
"check gas pressure if inadequate heater will soot and overheat if gas ok you might need a..."
David Spradling posted an answer for this Honeywell Pool & Spa:
"check to see if filters dirty make sure wires are tight to pressure switch make sure..."
David Spradling posted an answer for this Jandy Aqualink RS8 Pool/Spa Combo Control System:
"means bad water temp sensor or cut wire to it"
David Spradling posted an answer for this AO Smith A O Smith Motors Century 1hp 115v Thru - Bolt Lomart Motor - Bv90:
"or air leak at intake of pump try tightening union"
David Spradling posted an answer for this AO Smith Pool & Spa:
"cannot buy bearings for motor must replace motor dont forget seals"
David Spradling posted an answer for this Jandy Aqualink Rs4 One Touch Control System Control System:
"push button below auto service and time out 1 time to put it in auto"
David Spradling posted an answer for this Jandy Pool & Spa:
"check breaker if ok check relay"
David Spradling posted an answer for this Jandy Lite 2 Natural Gas Pilot Light Heater:
"cannot bypass need new one"
David Spradling posted an answer for this Jandy Laars Lite 2 Pool Heater 125,000 Btu / Propane Gas :
"need new pilot generator"
David Spradling posted an answer for this Jandy Laars Lt 400,000 Btu Heater:
"means its not heating red light means it is working"
David Spradling posted an answer for this Pool & Spa:
"check fuses inside front panel sounds like a shorted heater element"
David Spradling posted an answer for this Pool & Spa:
"need new pilot generator"
David Spradling posted an answer for this Pool & Spa:
"yes look at gas valve turn to pilot hold down for about a minute then light pilot..."
David Spradling posted an answer for this Jandy Laars Lite 2 Pool Heater 250000 BTU Propane Gas (Spark Ignition):
"check the fuses going to the ignitor if ok ohm out ignitor to see if shorted or open..."
David Spradling posted an answer for this Jandy AQUALINK RS TELELINK KIT :
"make sure 4 pin connector for aquapure is plugged into multilex board so you can see it"
David Spradling posted an answer for this Jandy Aqualink Rs4 One Touch Control System Control System:
"make sure wire isnt shorted"
David Spradling posted an answer for this Jandy AQUALINK RS TELELINK KIT :
"check to see if JVAs are on and in the correct position"
David Spradling posted an answer for this Jandy AquaLink RS2/6 All Button Dual Equipment - :
"turn system off then try again make sure wire connecting to controller is plugged in and..."
David Spradling posted an answer for this Jandy Aqualink Rs4 One Touch Control System Control System:
"check breaker then check the relay for that aux"
David Spradling posted an answer for this Jandy AQUALINK RS TELELINK KIT :
"check to see if 4 pin red plug is plugged in and tight also check for cut wire"
David Spradling posted an answer for this Jandy Laars LX Pool Heater / 400,000 BTU / Natural Gas:
"check to see if fusible link is good then check hi limits they are by the plumbing inlets"
David Spradling posted an answer for this Jandy Aqualink Rs4 One Touch Control System Control System:
"check for cut or exposed wires to controller or see if 4 pin pug is connected and tight"