Saeco ODEA - Recent Questions, Troubleshooting & Support


Did you check if your hot water know was fully closed

Try turn off the machine, press the water drop button and turn on the machine . Keep pressing for 20 sec.

You may attached a recording video if problem not resolved

Good luck

Saeco Odea Giro... | Answered on Jan 16, 2019


Descale in the water tank...press nd hold water button and the mechine will do the rest automatically u jst hv to turn on or of the water knop...drawer take it out and take out the brewing unit put them back again thats it.
1_15_2019_10_09_47_am.jpg

Saeco Odea Giro... | Answered on Jan 15, 2019


There are different possibilities for your problem. First the motor might be damaged and is more weak than before that is why is stop when it need to grind beans. In this case only with replacement motor can solve the problem.

Second probably due to long use of oily coffee or low quality coffee beans or other reason there are coffee grounded in the grinder that become like rubber and does not leave the new coffee to pass through grinding burrs. For this either you have to dismantle the whole grinder and its burrs and clean them with brush or you can use a new magic product that you can fin in eBay it can clean automatically the grinder in 30 second see it at the link

http://www.ebay.com/itm/PULY-GRIND-COFFEE-GRINDER-CLEANER-CRYSTALS-20-GRAMS-PACK-OF-3-PACKETS-/131031511160?ssPageName=STRK:MESE:IT


You can try the above fist and you may solve the problem in minutes if not then you can proceed with the replacement of the ginder burrs or motor.

Saeco Odea Go | Answered on Mar 13, 2018


First, you're going to need to get the brew group out. Check this out to get the brew group out. You need to remove a screw and pull unless you're really crafty.

This video will help.
After that:

a) Yes, lubing will help.
b) Replace the o-ring on the piston in the brew group (it should be orange). It gets old and gummy creating resistance.
c) Reinforce the weak plastic that gets over-torqued.

I own three of these units, one from 2007 (made in Italy, never broke, has tens of thousands of brews) and two newer units (made in Eastern Europe, fewer brews, both broke). I can distinguish the newer ones because they have a "sleep mode". They really overtorque the gear.

I tried repairing with just glue and that lasted (surprisingly) several months. I tried again by using a thick paperclip as a drill bit and that lasted 7 months.

Now with the holes piloted, I drilled a little wider and put in heavier metal from a heavy-duty binder clip. Cheap and very strong! Let's see how long this lasts.

See before and after pictures. This metal won't bend!




saeco 1-s3l51ixtlnjbpncvr5acfykc-1-0.jpg

saeco 2-s3l51ixtlnjbpncvr5acfykc-1-2.jpg

saeco 3-s3l51ixtlnjbpncvr5acfykc-1-5.jpg

saeco 4-s3l51ixtlnjbpncvr5acfykc-1-9.jpg

saeco 5-s3l51ixtlnjbpncvr5acfykc-1-14.jpg

saeco 6-s3l51ixtlnjbpncvr5acfykc-1-20.jpg

saeco 7-s3l51ixtlnjbpncvr5acfykc-1-35.jpg

saeco 8-s3l51ixtlnjbpncvr5acfykc-1-44.jpg

saeco 9-s3l51ixtlnjbpncvr5acfykc-1-54.jpg

saeco 10-s3l51ixtlnjbpncvr5acfykc-1-77.jpg

Saeco Odea Giro... | Answered on Mar 07, 2018


have you tried adjust coffee strenght?
This is the bean symbol on the bottom of the front control

Saeco Odea Go | Answered on Mar 03, 2018


when the red light blinking it means machine must be primed. BUT if you prime it and still red light -you have to change the FLOWMETER.

Saeco Odea Go | Answered on Jan 14, 2018


hi,
when the machine is On for long time ,it going in the STAND BY MODE-green light is flashing slowly.Just press coffe button and wait for a 10 seconds.
When the red light is ON and no flashing it is mean there is no water in the water tank or too much water in the drip tray.

Saeco Odea Go | Answered on Jan 14, 2018


First, I'm Not a Saeco Representative, though I have worked on some Saeco machines.
** Most cases of one side not dispensing coffee is usually coffee that has dried and built up over time to coat the least used spout. This is caused by the machine not being flushed or cleaned daily.
** Follow the MFR's daily cleaning instructions to keep you unit operating properly.
** fill a glass up of water to the rim and place on drain tray. the water in the cup should be even with the glass lip all around the cup. If it's leaning to one side then your machine (or table it on) needs to be level in order for the spout to dispense evenly. Another way to check is to place 2 shot glasses under each spout and brew a double shot. Both should fill at the same time and be the same amount when finished.
** Check your MFR's kit to see if there is a small brush to allow for nozzle cleaning. Otherwise follow the cleaning instructions and do multiple cleanings to get rid of the coffee residue. Once cleaned you need to maintain a regular cleaning schedule.
** There are no serviceable parts in these small home machines. Suggest contacting your vendor or Saeco for service or replacement.
Aloha! ukeboy57

Saeco Odea Giro... | Answered on Dec 21, 2017


There are multiple models that are listed as Odea Go series. Unfortunately the espresso community does not speak highly of these machines because of the low quality parts and assembly processes. The manufacturer for this unit has changed several times.

Saeco Odea Go | Answered on Nov 04, 2017


SEE THE VIODEO AND OTHER LINKS ON TYHAT SAME PAGE:

ALSO:
Saeco Odea Go adjusting coffee dose Questions

Saeco Odea Go | Answered on May 21, 2017

Not finding what you are looking for?

-222 questions posted

Ask a Question

Usually answered in minutes!

Top Saeco Coffee Makers & Espresso Machines Experts

Pierre Laplante

Level 3 Expert

2042 Answers

Ray Murphy

Level 2 Expert

68 Answers

eyecam

Level 2 Expert

96 Answers

Are you a Saeco Coffee Maker and Espresso Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Saeco Coffee Makers & Espresso...

  • Forum

View Most Popular

  • Saeco Coffee Makers & Espresso...
Loading...