Ricoh Office Equipment & Supplies - Page 7 - Recent Questions, Troubleshooting & Support

MPC205, or MPC2050? Try resetting the machine. https://www.google.com/search?q=RICOH+MPC205+reset Videos on changing the toner bottle procedure. https://www.google.com/search?q=RICOH+MPC2050+waste+toner+full .. ..

Thermistor failure. https://www.google.com/search?q=Ricoh+Aficio+MP-6500.+Error+message+SC+551 ..

1Press the "Clear Modes" button. This button will be on the main panel of the Ricoh copier.

2Press the "1,0,7" keys in succession. You do not have to hold the buttons down at the same time but need to press and release them in this exact order.

3Press and hold the "Stop" key. You will need to hold this button down until the Ricoh copier enters into service mode. The touch screen display will read "service mode" and three soft keys will appear.

4Press the "exit" button. This button will be on the touch screen display in the upper right hand corner. Once pressed, the copier will return to normal operation mode.

5Turn off the main power. The main power button will be located on the side or front of the copier, depending on which Ricoh model you are working on.

6Turn the power back on. Once the copier is powered back up, the service code will be cleared.

Hello!

I believe that you closed all the doors properly...

Well, this may happen because off several things.

I can give you some tips (by steps):

- First you have to make sure that the toner bottle spins (if that doenst happen it could be a faulty clutch).
- Than you need to see if the tonner supply (the green handel that you place the toner) are good.
- After that you just have the TD sensor. This sensor is on the Developement Unit.

Well, i am just giving you a clue. If you do not have thecnical knoledge i advise you to call your provider.

See you, And good luck

hi SOURCE: ricoh aficio 2022 error code sc542 1. Mode(Yellow Button) 2. 107 3. Press STOP Button for 3 second (RED Button) 4. Copy Sp 5. 5810# 6. Excute 7. Power Off 8. Power On

SOURCE: ricoh ft3713 error code e54, where is the fuser and thermistor you need a tech. this code can be caused by a software problem in the main board. it can also be caused by the machine overtoning, needing a pm.

The mechanical counter is either unplugged or is defective.

I have a Recoh MP C5201. I was reading USB pen drive before but now when you slot in ant usb pen drive,it displays that an incompatible usb has been installed.USB has been enabled but can not read it.How can I solve this problem. Regards, Bentil

https://printcopy.info/?mod=erc&brand=Ricoh&model=MP5000&code=220

E54 is a fusing error. You can attempt to reset the code by entering service modes. To do that, you press CLEAR MODES key, then the numbers 1, 0, and 7 and then hold down STOP key. Once in service mode, press 97 then #. That resets the code. Power the machine off then back on to see if it comes back. If it does, then you may need main board or AC driver board.

Possible fixes from previous FIXYA question. Use Comment menu to add information. For example, what model Ricoh printer is it? Have you replaced toner recently? If so, was it Ricoh original or not? http://www.fixya.com/support/t26593905-printer_ricoh_sp_210su_service_call Printer Ricoh sp 210SU service call error SC491 using compatable cartridge...

Needs more RAM memory to process the print job faster. If the Printer has upgradeable memory, you can speed it up. Crucial.com sells memory for HP printers, so they may have ricoh as well.

https://printcopy.info/?l=en&mod=erc&brand=Ricoh&model=Aficio%20SP5200DN&code=542

https://printcopy.info/?mod=erc&brand=Ricoh&model=IMC300&code=SC545-01

Richo2014. 220-00 service call

I have run into this several times with these printers. In every case, it has been the CMY PCU. These run about $300.

I have read that by cleaning the PCU, you can get it to work sometimes. So far, I have not been lucky enough for it to work.

Print Ready Temperature Error ?? The heating roller temperature increase during a set time is not correct. ?? The fusing temperature does not reach the print ready temperature within a set time after the fusing lamp has turned on. ?? Defective thermistor ?? Incorrect power supply input at the main power socket ?? Defective fusing lamp 1. Check the voltage of the wall outlet. 2. Replace the fusing unit 3. Replace the fusing lamp. **Execute "Engine Maintenance Menu" to recover the machine after completing the recovery procedure. Otherwise, the machine continues to issue this SC code and cannot be operated.

93300 HRB (Head Relay Board) fuse blown Mounted on the top part of the carriage unit.

Ricoh SP C261SFNw printer error SC 542 5. Execute "Reset Fuser Unit" with the "Engine Maintenance" menu if the fusing unit is replaced. "Menu Mode" can be executed by depressing the following key sequence while in ready condition: Clear/Stop, 1, 0, 7 and Color Start. (Press and hold each key till a beep is heard.) 6. Scroll to Engine Maintenance - Enter 7. Scroll to Reset Fuser Unit - Enter