Pioneer Televison & Video - Recent Questions, Troubleshooting & Support


Hello Michael, indicate the model of your TV pioneer
Test if the remote control works, remove the batteries, observe the contacts of the batteries, which are clean, otherwise, clean them so that the batteries make good contact
Once the batteries and contacts have been checked, put them back
Take your cell phone, put it in camera mode and point the emitter LED of the remote control to the camera, press the keys and see if the emitting LED lights up, if so, try directly with the TV
if it does not turn on, you could carefully disassemble the remote control and clean the contacts and the rubber keyboard internally, Do not Use Alcohol to clean
the rubber keyboard, you can clean it with warm water and detergent then let it dry very well, the contact plate, you can use a cloth with a little liquid to clean the glasses, the idea is to remove the rubber residue that is on the contacts
then arm again and try, if not you have results consult a specialized technical service and if you try, you see in the camera that the LED turns on, but the TV does not, then it takes the two devices to the specialized technical service
I hope you can solve the problem
Greetings Franco Dosil

Hola Michael, indica el modelo de tu TV Pioneer
Prueba si te control remoto funciona, s?cale las pilas, observa los contactos de las pilas, que se encuentren limpios, sino es as?, limpialos para que las pilas hagan buen contacto
Una vez controlado las pilas y contactos,vuelve a colocarlas
Toma tu celular, pon en modo c?mara y apunta el Led emisor del control remoto hacia la c?mara, presiona las teclas y f?jate si se ilumina el Led emisor, si es as?, prueba directamente con el TV
sino prende, podr?as desarmar con cuidado el control remoto y limpiar internamente los contacto y el teclado de goma, No Uses Alcohol para limpiar
el teclado de goma, lo puedes limpiar con agua tibia y detergente luego d?jalo secar muy bien, la placa de los contacto, puedes usar un pa?o con un poco de liquido para limpiar los vidrios, la idea es sacar el residuo de goma que hay sobre los contactos
luego arma nuevamente y prueba, sino tienes resultados consulta a un servicio t?cnico especializado y si pruebas, ves en la c?mara que el Led se enciende, pero el televisor no, entonces lleva los dos aparatos al servicio t?cnico especializado
Espero puedas resolver el problema
Saludos Franco Dosil

Pioneer... | Answered 16 hours ago


Hello Michael, indicate the model of your TV pioneer
Test if the remote control works, remove the batteries, observe the contacts of the batteries, which are clean, otherwise, clean them so that the batteries make good contact
Once the batteries and contacts have been checked, put them back
Take your cell phone, put it in camera mode and point the emitter LED of the remote control to the camera, press the keys and see if the emitting LED lights up, if so, try directly with the TV
if it does not turn on, you could carefully disassemble the remote control and clean the contacts and the rubber keyboard internally, Do not Use Alcohol to clean
the rubber keyboard, you can clean it with warm water and detergent then let it dry very well, the contact plate, you can use a cloth with a little liquid to clean the glasses, the idea is to remove the rubber residue that is on the contacts
then arm again and try, but if you have results consult a specialized technical service and if you try, you see in the camera that the Led is turned on, but the TV does not, then it takes the two devices to the specialized technical service
I hope you can solve the problem
Greetings Franco Dosil

Hola Michael, indica el modelo de tu TV Pioneer
Prueba si te control remoto funciona, s?cale las pilas, observa los contactos de las pilas, que se encuentren limpios, sino es as?, limpialos para que las pilas hagan buen contacto
Una vez controlado las pilas y contactos,vuelve a colocarlas
Toma tu celular, pon en modo c?mara y apunta el Led emisor del control remoto hacia la c?mara, presiona las teclas y f?jate si se ilumina el Led emisor, si es as?, prueba directamente con el TV
sino prende, podr?as desarmar con cuidado el control remoto y limpiar internamente los contacto y el teclado de goma, No Uses Alcohol para limpiar
el teclado de goma, lo puedes limpiar con agua tibia y detergente luego d?jalo secar muy bien, la placa de los contacto, puedes usar un pa?o con un poco de liquido para limpiar los vidrios, la idea es sacar el residuo de goma que hay sobre los contactos
luego arma nuevamente y prueba, sino tienes resultados consulta a un servicio t?cnico especializado y si pruebas, ves en la camara que el Led se enciende, pero el televisor no, entonces lleva los dos aparatos al servicio t?cnico especializado
Espero puedas resolver el problema
Saludos Franco Dosil

Pioneer... | Answered 16 hours ago


Google the manual or try the manufacturers web site for it if there are no external control buttons.

Pioneer... | Answered on May 19, 2019


Power up and press open button as soon as it starts to spin, some dvds lock with read errors, some spit the disc out..
If the belt is worn open unit, remove tray and replace rubber belt, if you dont have one use a thick rubber band.
if you cant access rubber belt, most dvd's have a slide underneath. use a small screwdriver and manually slide it open.
Read errors are not always the laser...so dont go and waste money.
If your dvd is not hq using dc brushless motors, remove loader, give the spindle and sled motor a good lube with wd40, spin the spindle moto up with 5-7 volts to clean the commutator.
Carbon builds up and the motors dont spin at correct speed.
Sled remove drive gear, usually pops out and burn it clean as above.
I have had good results with above since 2004, repaired 1000's of dvd's over my 14 years as senior engineer for wholesale importer in cape town.
Good luck
44ct357 CT SA

Pioneer DV-C503... | Answered on May 19, 2019


Solution for Pioneer DV-C36 Multi Disk DVD player - tray door will not stay open.

My player would open the disk tray when the open button was press but when the tray was fully open it would retract
back into the unit leaving no time to change or load disks.
I found a poor connection at the ribbon cable connector was causing this problem. A seven conductor ribbon cable
connects the main unit with the travelling tray. A position switch (S21) senses when the tray is fully extended and retracted.
On my player pin 1 of the ribbon cable connector on the travelling tray was not making an electrical connection which
causes the control system to retract the tray. The fault lies in the connector - the tang was not pressing against the ribbon cable conductor.
I was able to desolder the connector and pull the contact out just far enough to reform the tang with fine needle nose pliers.
This is very tedious and required an eye loupe for magnification.
Tools required:
#1 and #2 phillips screwdrivers
Soldering and desoldering irons (or other desoldering tools)
Fine needle nose pliers.

Remove the tray ribbon cable
1. Remove the cabinet cover - 6 screws. Open the tray. To keep the tray from retracting pull the power cord when the tray is extended.
2. Remove the front bezel from the tray. Gently pry up the bezel by relesing the catches with a small screwdriver. Allow the tray to retract.
3. Remove the front panel - undo large ribbon and wire connections on right, remove screws left and right, release
two catch tangs on bottom edge using a small screwdriver on the inside of the unit.
4. Remove the white plastic cover over the laser mechanism ( 2 screws) Remove the disk carrier by removing the center screw.
5. Extend the tray again. When the tray is out the small ribbon cable is visible below the tray. Undo the ribon cable where it attaches to the main unit unit.
6. To slide the tray off the main unit use a small screwdriver to depress the stop catches (2) in the tray. They are molded into the tray.
Pull the tray out further then lift up.
7. Flip over the tray and find the small circuit board the ribbon cable goes to. Desolder the motor wires (red and black) and remove the 2 screws
holding the circuit board and position switch.

Use a multimeter to confirm there is an open or poor connection in the ribbon cable connector.

Remove the ribon cable and inspect the connector with an eye loupe or other magnification device. On my player contact #1 was not positioned properly
to press against the ribbon cable conductor. You can either replace the connector or repair it.
Warning: repairing the connector may damage it.
To repair the contact desolder the connector from the circuit board. Bend the circuit board prong straight and push it into the body of the
connector which will extend the contact out and the contact can be reformed. Be very gentle. Bending the contact may cause it to break.

Reassembly is the reverse. Don't forget to solder the motor wires with the proper polarity. Red and Black are labeled on the circuit board.

Pioneer DV-C36... | Answered on May 10, 2019


This could be an issue to do with your power board. You need to see a qualified tech. Also, ask this on this link http://electronics.co.ke/

Pioneer... | Answered on May 08, 2019


8 or 12 blue blinks repair service on eBay, item#123220417873

Pioneer... | Answered on Apr 25, 2019


Replace the main assy

Pioneer... | Answered on Apr 25, 2019


I would assume the power board has a problem. A tech could possibly repair it without replacing the whole board.

Pioneer... | Answered on Apr 22, 2019


Try restting it by unplugging the tv for a few mins and it should rest to original factory default settings but leave it unplugged 10-15 mins to be sure.

Pioneer... | Answered on Apr 21, 2019


The following article just aims to provide a step by step guide on how to convert 1080p or 720 p MKV to DVD format as well as burn MKV to DVD for playing MKV on DVD player successfully at How to Play 1080p or 720p MKV on DVD Player?

This guide can easily help to:

Convert 1080p MKV to DVD format to burn 1080p MKV to DVD
Convert 720p MKV to DVD format to burn 720p MKV to DVD
Convert MKV files in other resolution to DVD to burn MKV to DVD for play MKV on DVD player
Convert and burn MKV to DVD for successfully playing MKV files on any kind of DVD player
Convert and burn other video files including AVI, WMV, MP4, MPG, FLV, AVCHD, MOV, 3GP, WTV, MXF, and etc to DVD

Pioneer... | Answered on Apr 07, 2019


Request directly from Pioneer.

Pioneer... | Answered on Mar 30, 2019


That model doesn't support 1080p
Change to 720p and you're done

Pioneer... | Answered on Mar 28, 2019

Not finding what you are looking for?
Pioneer Logo

4,086 questions posted

Ask a Question

Usually answered in minutes!

Top Pioneer Televison & Video Experts

The Knight
The Knight

Level 3 Expert

76046 Answers

Jaime Hernandez

Level 3 Expert

2337 Answers

Marvin
Marvin

Level 3 Expert

84625 Answers

Are you a Pioneer Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...