Leviton Electrical Supplies - Recent Questions, Troubleshooting & Support


most if not all these padlocks when first manufactured the manufactures has to set it with some digits if it four digits lock , manufacture use eg., 0000 or 1234 and if it six digits it uses 000000 or 123456 and so on the idea is that when the lock is first bought it comes with these digits then by following their instruction you can change the code you wish to have

Leviton 8299... | Answered on Jan 02, 2018


yes, take the white wires off the switches and splice them all together with a wire nut. Run a hot wire to each of the switches and then run the switch leg (black) from each of the fixtures to be controlled to each of the dimmers.

Leviton... | Answered on Dec 18, 2017


How many wires are on the dimmer switch and what
colors are they ? How many wires were attached to the old switch ?

Leviton MFG... | Answered on Dec 18, 2017


If the two load screws are connected with a tab that is the power in side. The color wires are the load.

Leviton... | Answered on Nov 03, 2017


Seems to be a common problem, you're not alone ( read amazon 1 star reviews). They are $22.00 so you will to dispose of it, if
Leviton will not warranty it.

Leviton... | Answered on Oct 27, 2017


LOL.. I had this same problem... I simply removed one switch and turned it upside down...now the levers are in the same position when they are off...

Leviton... | Answered on Jul 18, 2017


I think putting the card in and out of your phone may have slightly changed the alignment of the card to the connectors in the phone - try entering the card either to the left a little or the right but i have a feeling contact is not being made from the wear and tear. Does the card work in another phone? if yes then definitely not the card... but the fact that you have tried to use 2 different cards im thinking its the phone :(

Leviton Combo... | Answered on May 06, 2017


It sounds as though the wires coming in to the back side are
9 back stabbed ). With the power off, grip the back stabbed wires one at a time and pull as you twist the receptacle side to side. the wires should back out.

Leviton 8299... | Answered on May 01, 2017


Typically in three way residential switching the Red and White are used as travelers from 3 way to 3 way. That in mind, connect the black to black, red to one red and the other red to the white. mark the white wire with black tape.

Leviton... | Answered on May 01, 2017


Connect the green dimmer wire to your ground wire

Leviton Anywhere... | Answered on May 01, 2017


most likely the type of lamps/bulbs you have are not compatible with the dimmers.

Leviton... | Answered on May 01, 2017


If there is a ground wire there and it is attached it should read correct. It may also indicate that there is a loose or missing ground wire somewhere else in the circuit.

Leviton 8599... | Answered on May 01, 2017


the 5641 is a dual switch for three way and single pole. If you want the switches to operate the CF. Connect the power to one of the two screws on the right side as you face the switch. then connect one wire to the screw on the bottom left side. connect the other screw to one of the two screws on the top left. This assumes the Red and Black you mentioned are the switch legs going to the CF.

Leviton... | Answered on May 01, 2017


You need to verify if there are two wires coming to the wall switch from the receptacle. One should be power in, the other should be power out to the receptacle.

Leviton... | Answered on May 01, 2017


Either the GFI is bad or it is tripping because there is a short in the system (obviously, right). I would turn off your panel break, disconnect the GFI and using a meter test to see if there is a short in the system. You would check the hot lead coming from the GFI to the tub and see if it is shorting. If you can't find a short, you should try replacing the GFI. If there is a short then you need to search for the short. Hope this helps and good luck!

Leviton 8599... | Answered on Apr 19, 2017


Yes you short circuited the dimmer switch, it requires replacement to dim the light.

Leviton Decora... | Answered on Apr 06, 2017


Unless your switch is very, very different from all the other switches I have used, simply connecting the ports to live systems is all you need to do. Have you tried this?

It may be that the patch panel is not wired, and that is kind of a pain.

Leviton 5225WSP... | Answered on Mar 02, 2017

Not finding what you are looking for?
Leviton Logo

601 questions posted

Ask a Question

Usually answered in minutes!

Top Leviton Electrical Supplies Experts

 Kenneth
Kenneth

Level 2 Expert

50 Answers

Steve

Level 3 Expert

3289 Answers

Hippy_dd

Level 2 Expert

112 Answers

Are you a Leviton Electrical Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...