Kodak EasyShare - Recent Questions, Troubleshooting & Support - Page 7

it does not have ethernet adapter according to the specs no no ip address or interface ?. Do you have the optional bluetooth adapter with the printer. ? You may be able to connect via bluetooth http://classroom.synonym.com/make-kodak-printer-wireless-bluetooth-17749.html http://support.en.kodak.com/app/answers/detail/a_id/1157/selected/true http://www.amazon.com/Kodak-Wireless-Adapter-Printer-Dock/product-reviews/B0006NMSK6

To resolve this error:

1. Disconnect the power adapter from the printer.
2. Wait 30 seconds to allow the printer to reset.
3. Connect the power adapter to the printer. Turn on the printer, if necessary.
4. for more help visit https://cbrtechsolutions.net

turn off the printer
unplug the power chord at the back of the printer
wait for 5-10 sec.
replug power chord
turn on the printer

Replace cartridge, but, before run the print test (cartridge alignment as well as cartridge cleaning process).

Run a "print-head-cleaning-cycle" -- the ink inside the cartridges is not getting through the ink-jets, and is not reaching the paper.

Either that, or the electronics inside the ink-jets are malfunctioning, i.e., not telling the ink-jets to shoot the ink out.

maybe the ink jet cartridge is depleted. This is common on all ink jet printers.
Or, the ink jet cartridge has tape on the head.

This one pops up a lot when the printhead sensor gets dirty. I would pull the paper out, give the inside a good blast of canned air, pull the cartridges and then reload it like you're setting it up again the first time: paper, ink, test print. If you still get the error code try cleaning it again but on its side or back and check the print head belt and rail, too.

Maye a sensor is broken or dirty. I guess I would start by cleaning the inside of the printer with alcohol. Also, see if there is any paper stuck in it.

If you haven't bought one, just get another (maybe Brother) printer. Kodak printers eat heads for breakfast.

Can you tell me how the head was jammed in the first place. Is the head jammed in the middle of the carriage? If it's jammed in the dock then you might need to open the covers. Then you need to investigate further. If your not confident with mechanical parts that could be a problem. The obvious one "switch off and on, try resetting the mechanicals" possibly severlal times.

Contact the manufacture for a list of distributers in your area.

Try Using An HP Color Inkjet Printer With Only 2 Cartridges, One Color One Black That Works! If You Don't Have One Buy One New or Used It Does not Matter HP Is The Best! the one you have Is Defective Anyway And Needs To Be Replaced!

Hi, if nothing happens when scanning w/ your printer.Please follow the steps below.

1.Verify that the scanner is working properly by copying a document first.

2. Open the Kodak AiO Home Center software.

3. Select Configure Settings.

4. Click Scan.

5. Click either the Documenttab or PictureTab depending on the file you want to scan.

6. Under File Save Setting, sure that the Prompt for filename and location is selected.

7. Click Apply then OK.


Thanks.

Regards,

Neerak21

http://www.kodak.com/global/en/service/products/ekn035496.jhtml?pq-path=12814
Click on Software Downloads

1. if you have CD came with printer, please keep in the cd rom and goto my computer -> cd driver-> double clik setup.exe. and follow the instructions.

Otherwise. ....

2.
Please download the files from http://support.en.kodak.co.in/app/answers/detail/a_id/36555/selected/true
and follow instructions
Installation Instructions

1. Verify that your computer meets the system requirements.
   WINDOWS XP 64-bit Operating System is not supported.
2. Disconnect your all-in-one printer from your computer.
3. Verify that you logged on to the computer using the administrator account.
4. Close all programs.
5. Download the software onto your computer.
6. Double-click the *.exe file, then follow the on-screen instructions.
7. When the installation is complete, connect your all-in-one printer to your computer.
8. Select Start > Programs > Kodak > Kodak AiO Home Center.

Hope this helps to yoy

Is it a non Kodak band?

u can solve this problem from page setup.