KitchenAid Ovens - Recent Questions, Troubleshooting & Support


Hello Susan Bailey,
Typically "THEY" do...
It would be really great to know if we are talking about a USA domestic product...
or another NATIONALITY.
Other countries normally have FUSES in the
appliance cords.

Find your MODEL NUMBER and go to a PART/SPARES
supplier ( I like appliancepartspros.com )
-> appliancepartspros.com
If this is a "MICROWAVE" the FUSE will start popping because the MAGNETRON has deteriorated
and is CONSUMING it's own energy.

I can be a LOT MORE specific if you provide a
model number (pretty please).
Read minds... Cannot rally do...!!
https://en.wikipedia.org/wiki/Carnac_the_Magnificent

KitchenAid Ovens | Answered on Jun 25, 2019


F5 - E1 Self clean latch will not lock

1. If door latched:
  1. Disconnect power from unit.
  2. Check wires and connectors from control to door switch, then from door switch to control. If no damage to wires and all connectors okay, proceed to step C.
  3. Replace door switch.
  4. Re-apply power.
  5. Press and hold any key down for 1 minute to clear F5 failure code from memory. F2 will appear. Press CANCEL and observe for 1 minute to ensure operation is correct.
2. If door not latched:
  1. Disconnect power from unit.
  2. Check wires and connectors from control to latch switch, then from latch switch to control. If no damage to wires and all connectors okay, proceed to step C.
  3. Repeat steps A and B for door switch.
3. Measure door switch (door open = switch open small low voltage terminals). Replace switch if defective.
4. Measure latch switch (unlatch = switch open, CAUTION - oven light contacts are closed). Replace switch if defective.
5. If corrections are made in any step, reconnect power to control. Press and hold any key for 1 minute to clear R failure code from memory. F2 will appear. Press CANCEL and observe for 1 minute to ensure operation is correct.
6. If failure remains, disconnect power and replace control.

Note: Applies to all F5-E... codes.

KitchenAid... | Answered on Jun 19, 2019


Hi. try to reset this unit by killing the power or unplugging the cord for 5 minutes. this will reset the control. if the control continues to beep after you reset, this will confirm control failure. you will need to replace the control board in this case.

KitchenAid... | Answered on Jun 19, 2019


I am having the same problem, how did you fix it?

KitchenAid ... | Answered on Mar 01, 2019


Possible Solutions

Reset power to the product:

There may be a problem with the Oven Appliance Manger Control or the associated wiring.
  • Power unit down by turning off the circuit breaker(s) for one (1) minute.
  • Power unit up by turning on the circuit breaker(s).
  • Monitor the oven for one (1) minute to ensure the error code does not display again.
  • Verify oven operation.

Still need help? Call or schedule service.

KitchenAid Ovens | Answered on Feb 02, 2019


probably bad ignitor see if it glows if not replace

KitchenAid Ovens | Answered on Sep 15, 2018


F6 - E0 Return line not connected If switch pulse return line is not connected, electronic control will display F6 within 60 seconds after power up. Replace control board

KitchenAid... | Answered on Aug 16, 2018

Not finding what you are looking for?
KitchenAid Logo

1,073 questions posted

Ask a Question

Usually answered in minutes!

Top KitchenAid Ovens Experts

Marvin
Marvin

Level 3 Expert

85111 Answers

jdthefixer

Level 3 Expert

745 Answers

Craig Butler
Craig Butler

Level 3 Expert

1730 Answers

Are you a KitchenAid Oven Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...