Jet Tech Systems Refrigerators - Popular Questions, Answers, Tips & Manuals


Make up a way to blow warm air from the condenser over the glass and your frost problem will disappear! The higher the temperature of the air - the more moisture it can absorb. The reason you are having the problem is that you are cooling moisture laden air and it has to give up the moisture as you cool it. So run some warm air over it and it will absorb the moisture for you = problem gone.

koolman77 (refrigeration technician)

Jet Tech Systems... | 66 views | 0 helpful votes


Request the diagrams directly from Igloo.

Refrigerators | 245 views | 1 helpful votes


Frostless freezers will go into a defrost cycle periodically and the frost that accumulates in the freezer section melts and runs into a pan under the refrigerator section, through a drain hose. If this hose clogs with crud (common) the melt water can't drain and leaks into refrigerator section (or it was designed this way so as to prevent refreezing.) As the drain is clogged, thd water builds up until it overflows to floor level.

You need to locate the drain in bottom of the refrigerator section (usually near the back where its hidden from view) and clear it out. (Use care as its usually only a vinly hose and can be punctured or slipped off its connection).

Refrigerators | 284 views | 1 helpful votes


will need to sand down to metal no rust then primer then repaint --or spray or wire on a rust away product most auto or home stores carry it

Refrigerators | 189 views | 1 helpful votes


P1 is usually the code for a temperature probe error - the refrigeration should now operate on a time cycle until the temp probe is replaced

Refrigerators | 229 views | 1 helpful votes


Need a little more info, but it should have a removable container that hold the ice. That comes out. If it is too jammed up with ice to move it, you will have to carefully chip away at some of it, or let it thaw. Once you are able, take the container out and empty it completely dry it out. If that doesn't do it, there is a problem with the mechanism.

Refrigerators | 303 views | 2 helpful votes


short -seized--thermal safety fail electrical circuit problem

Refrigerators | 285 views | 1 helpful votes


Depends on the settings you set the frig and freezer to , as soon the settings are reached it should shut off, anything longer than a few hours points to a fault.

Refrigerators | 959 views | 0 helpful votes


Google

make model remove freezer drawer

impossible to guess what you have.

Refrigerators | 725 views | 0 helpful votes


Defrost and switch power after 24 hours

Refrigerators | 894 views | 0 helpful votes


Have you reset the icemaker? Usually there's a lever or switch that you have press to reset it. You did not post the make/model of your fridge so it's difficult to say which reset device you have.

Refrigerators | 447 views | 1 helpful votes


I could not locate a Whirlpool manual, but found the contact information for you to speak to Whirlpool and request assistance.

https://www.whirlpool.com/services/contact-us.html


Contact Us Save time by checking your appliance information before contacting us. Manuals and Literature
You can also visit our Product Help Page for troubleshooting tips.
Questions or comments? Here are a few easy ways to reach us.

By Phone

US: 1-866-698-2538
Canada: 1-800-807-6777
Hour of Operation:
Monday-Friday: 8:00 AM to 8:00 PM EST
Saturday: 8:00 AM to 4:30 PM EST
Please locate the appliance's model and serial number before calling.
Need help finding your model and serial number?

Chat

Hour of Operation:
Monday-Friday: 8:00 AM to 8:00 PM EST
Saturday: 8:00 AM to 4:30 PM EST
Launch live chat

By Mail

Whirlpool Customer Service
553 Benson Road
Benton Harbor, MI 49022

Refrigerators | 168 views | 1 helpful votes


before you spend a lot defrost/ unplug. lets the ice in the crossovers melt. plug it back in and see what you get.

mike

Refrigerators | 39 views | 0 helpful votes


Usually, this is caused by a stuck or bad evaporator fan. There are several other possible causes. The first thing that comes to mind is low freon.

Refrigerators | 40 views | 0 helpful votes


The model # is actually MFI and not MF1. The part for the bypass plug will be 12664501SP. Most people do not know what it is when they get their new fridge and throw it in a junk drawer! Look around as you probably have it somewhere.

Refrigerators | 197 views | 1 helpful votes


i don't know. a quick temporary fix would be to use a timer
[ rated strong enough ] to turn the power off and on for a while every so many hours.

Refrigerators | 37 views | 0 helpful votes


suspect it needs freon added and if not equipped with the fitting then only a pro can do it

Refrigerators | 444 views | 1 helpful votes


Same as if you were disinfecting any water-using appliance. Mix 1/2 oz of Clorox Bleach with one gallon of water and let this mixture soak for a period of time. If your are seeing mold in the location you mentioned, theres probably mold everywhere else as well.

Personally. I would increase to amount of bleach and make certain the mixture get into every nook and cranny.

Make absolutely certain that you rinse it out well afterwards.

Refrigerators | 34 views | 1 helpful votes

Not finding what you are looking for?
Jet Tech Systems Logo

1 questions posted

Ask a Question

Usually answered in minutes!

Top Jet Tech Systems Refrigerators Experts

Marvin
Marvin

Level 3 Expert

84966 Answers

Brad Brown

Level 3 Expert

18060 Answers

Gil Shultz

Level 3 Expert

3388 Answers

Are you a Jet Tech Systems Refrigerator Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...