INTELLINET Computers & Internet - Recent Questions, Troubleshooting & Support

Your problem is with the 524704 device. This is NOT a router - it is a wireless access point. It is designed to be connected TO a DHCP router that can assign separate and unique IP addresses to each device that the Access point connects to. The way you are using this device will not work with more than one device since the unit is forced to use the fixed IP address from the wireless access point to the modem and only one device can use any specific IP address. You need to get a wireless ROUTER to achieve you goals.

Best way to use your xbox 360 is with a stable internet connection wired to a router using dsl or fiber connection.

First, try changing the wireless channel to one within the range of 1 to 11, not more than 11Another possible solution would be degrading the Wireless-Mode, it may be set to N only mode, change that to G only, or B/G modeGood luck

Are you pertaining to your wi-fi password? Follow this instructions:1. connect via hard wired connection (network cable)2. open your internet explorer or any browser.3. type the numbers 192.168.1.1 on the address bar4. you will be routed to your router's settings, type admin for USERNAME: and admin for PASSWORD.5. look for the basic setup/settings6. look for the wireless settings7. under your SSID comes the WEP or WPA-PSK option8. that is your wi-fi password, then modified it and remember the password you use for you will need to enter it on your pc when you are connecting via wireless connection.you can select ASCII for password. it should be alpha numeric or combination of letters and numbers.9. select saveand apply. then you are good to go.

Wireless Zero Configuration (WZC) was introduced with Windows XP, it is also known as WLAN AutoConfig in Windows 7 and Vista. It is is a wireless connection management utility which dynamically selects a wireless network to connect to based on a user's preferences and various default settings. or most users the Windows Wireless Zero Utility is all that is needed to manage your wireless connections.

You can configure WZC as follows:

1. Type services.msc in "run" and enter.
2. Select wireless zero configuration from the list which appears in the next window.
3. Double click on that option , and choose to Start or Stop the Wireless Zero service.

Here are steps to use Wireless Zero Configuration/WLAN AutoConfig in Windows 7:

1. Click the Windows logo button
2. Type services in the Start Menu's Search box and press Enter. Scroll to the bottom of the list and locate WLAN AutoConfig'. Double-click WLAN AutoConfig to open its Properties window.
3. Click the General tab of WLAN AutoConfig service. Click the Startup type drop-down menu and click Automatic to have the service started automatically when the operating system loads. Click the Start button. Click Apply and then OK. Close the Services console window.
4. Click the Windows logo button. Type cmd in the Search box and press Enter. In the Command Prompt window, type netsh wlan show settings and press Enter. Look at the last line of the Wireless LAN Settings entry to see if the message Auto configuration logic is enabled on interface or Auto configuration logic is disabled on interface appears. If the entry notes that it is disabled, type, set autoconfig enabled=yes interface=Interface Name and press Enter. Close the Command Prompt window.

hello
is on the back,if is not there connect to router and u will see it in router setings
but as an advice change the securty sytem on the router , set it up for psk2 whit a shared key...easy to remember...

best regards

Have you followed the troubleshooting steps found in the manual at page 11? If you no longer have the manual get it from here
http://www.cradlepoint.com/files/uploads/CradlePoint_MBR1000_UserManual-v1.pdf

It's possible that the IP addresses for the printers got reassigned when the power came back on. Try uninstalling the printers and then reinstalling them as if you had new printers. (I know it's a pain to reload the software/drivers.)

If you have Windows 7, click Start > Devices and Printers (or Printers and Faxes, with XP). Right click on each of the printers and choose Remove device. (Alternatively, left click on the printer icon and then choose Remove device from the list of actions near the top of the Window.) Then reboot the computers. Finally reinstall the printer either using the CD that came with the unit, the software from the manufacturer's site or using the Windows driver with the Add a printer wizard depending on the printer and the driver availability.

I hope this helps.

Cindy Wells
(we only have one networked printer. However, we've had to reinstall the printer once. At least a few times, we've had the DHCP setting on the router give IP address conflicts after downtime.)

Connect your USB modem to the USB port located on the front

panel of the router.
2.

Connect your xDSL / cable modem to the WAN port of router by

Ethernet cable. NOTE: Go to Section 3-4 Fail Over to assign

the WAN connection priority if you have subscribed to both 3G
and xDSL/Cable Modem services.

Connect all your computers, network devices (network-enabled

consumer devices other than computers, like game consoles or
switches/hubs) to the LAN port of the router.

Connect the AC power adapter to the wall socket, then connect
it to the Power socket of the router.

Windows XP IP Address Setup

1. Click Start (at the lower-left corner of your desktop), then click

Control Panel. Double-click the Network and Internet

Connections icon, click Network Connections, then

double-click Local Area Connection; the Local Area
Connection Status window will appear. Click "Properties."

2. Select "Obtain an IP address automatically" and "Obtain DNS
server address automatically," then click "OK."
User Manual:
http://assets.mhint.s3.amazonaws.com/downloads/5805/524681_manual_english.pdf

I’m happy to assist further over the phone at https://www.6ya.com/expert/joe_8b8c2cd6ce148309

DICEUS with 13 years experience. SIMFORM for modernizing legacy architecture. ColorWhistle for leads. PixelCrayons for tailoring to your specific needs.

If you are in the middle of a contract, then cutting your wages is almost certainly a violation of your employment law rights. While I am by no means an expert on this matter, I did have a similar issue years ago - mid-contract wage cuts - and I hired anemployment attorney to fight the case on my behalf. It turned out that my employer was basically looking to scare people into taking the wage cut. They got into some pretty serious legal trouble for their transgression, and nothing happened to me in terms of wage cuts after that. If you are between contracts, your employer can re-negotiate your salary, but as far as I am aware, if you are in an agreed-upon contract, they cannot just decide to reduce your salary. If you want to settle matters, contest this action with support from a legal professional.