Hotpoint Logo

Hotpoint Popular Questions, Answers, Tips & Manuals

Do you work here? Claim your company

  • 532 Products
  • 82K Answers
  • 2M Views

Using your belt, slip it under the agitator. Give a very hard yank and the agitator will pop up and off. DO NOT HAVE YOUR FACE OVER THE AGITATOR WHEN YOU PULL ON IT. It can pop up with force, and end up breaking your nose! So be careful!

Hotpoint Washing... | 57 views | 0 helpful votes


CHECK SCREENS IN THE END OF THE HOSES .

Hotpoint Washing... | 28 views | 0 helpful votes


It sounds like an over temp sensor is tripping.....Make sure the lint filter is clean and no lint is blocking the vent pipe.........A fire hazard is present so be careful......Unplug the Unit while servicing the vent piping...........

Hotpoint Washing... | 20 views | 0 helpful votes


Go to www.repairclinic.com and enter WDL5490. With luck, you will be presented with a list of common replacement parts/assemblies and may be able to view a generic Hotpoint video showing disassembly with part/assembly identification.

Hotpoint Dryers | 33 views | 1 helpful votes


It depends on the reason for the hot smell - discovering this would mean a trip to the service shop and weighing the cost of that against a replacement microwave.

Unless your Hotpoint is something special, it is likely a replacement would make sense.

It is wise to periodically measure the power output of a microwave oven by timing the boiling of a measured quantity of water when it is young. When or if the time has extended more than about 10% it is time to think about service or replacement. It is also important to keep the inside of the cabinet clean and all the air vents clear.

Hotpoint Washing... | 31 views | 0 helpful votes


Best to contact the manufacturer or an appliance repair service. This is a car forum and we wouldn't have knowledge on you gas dryer.

Hotpoint Dryers | 28 views | 0 helpful votes


Remove the hose to the sensor switch at the tub end and check for obstruction. The small container on the side of the tub may be clogged. Clean with a small drill or piece of wire.

Hotpoint Washing... | 541 views | 0 helpful votes


There is a problem in the system, read the error codes.

Hotpoint... | 34 views | 0 helpful votes


The User Manual for this model was of no help ... other than to suggest unplugging the unit which you already did ...
I could not find specific error codes for your model ... but F06 on Hotpoint washers in general have two definitions for F06:

F06 - Door lock fault
Issue: Washing Machines door cannot be opened or closed / when the door is closed the machine the programme will not start.

F06 - Program selector dial

Since you are having door issues ... then I would say the door lock is indeed the problem.
Check to make sure there is not any debris in the door lock insert, but my guess is that is not your problem.
It could be the latch on the door or the lock switch mechanism in the machine housing. Odds are it is the locking mechanism

Here is a Hotpoint You Tube on how to replace ... but it is not for your specific model

https://www.youtube.com/watch?v=p14EEa4AYGM

Good luck with your troubleshooting!

Hotpoint Washing... | 135 views | 1 helpful votes


Contact manufacturer customer hotline phone# or google search Hotpoint oven UT47X. Marcus

Hotpoint Ovens | 441 views | 0 helpful votes


It is not going into a defrost cycle and you have ice build up between freezer supply vent it frig side. It could be a defrost timer, defrost termination switch or defrost heater problem.

Hotpoint... | 96 views | 0 helpful votes

Not finding what you are looking for?

Ask a Question

Usually answered in minutes!

Top Hotpoint Experts

Sal De

Level 3 Expert

2699 Answers

Marvin
Marvin

Level 3 Expert

84540 Answers

Brad Brown

Level 3 Expert

18031 Answers

Are you a Hotpoint Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...