Hoover Vacuums - Answered Questions & Fixed Issues


  • Defective battery
  • Defective charger

Hoover Vacuums | Answered 2 days ago | 22 views


go to hover for the owners manual sounds like it might be a clogged internal filter stifling the normal flow of cooling air around the motor

Hoover Vacuums | Answered on Dec 09, 2017 | 35 views


The V belt will stay " loose" until you lower the handle. Try replacing the flat belt and that should work.

Hoover U6437-900... | Answered on Dec 04, 2017 | 166 views


Pump fault? any filters which can be cleaned?

Hoover SteamVac... | Answered on Dec 03, 2017 | 4,402 views


Hi Bill.
Try this link
www.manualslib.com

Hoover Vacuums | Answered on Dec 02, 2017 | 30 views


You'll need a new switch, try these schematics.
Hoover U5491 900

Hoover Vacuums | Answered on Nov 28, 2017 | 178 views


Watch this video on youtube that I found, it shows a brushroll repair but it also shows the bottom plate removed and should be helpful!
Hoover Dial Matic Model 1120

Hoover Vacuums | Answered on Nov 28, 2017 | 29 views


In addition to the tab that contacts the bottom of the slider, there are 2 protusions on the adjustable wheel plate that move through holes in the housing, but only when the handle is tilted to begin vacuuming. The wheel plate has a spring that forces the tab against the slider. As the handle is moved to the upright position, the protusions move back through the holes, taking the tab away from the slider and the wheel plate locks in its highest position. Therefore, the position of the slider has no effect while the handle is upright and locked. Hope this helps.

Hoover U5753-900... | Answered on Nov 27, 2017 | 2,299 views


look here for help from the factory
https://support.neatorobotics.com/hc/en-us

Hoover Vacuums | Answered on Nov 26, 2017 | 19 views


The brush roller may be clogged with debris. If so, the belt will only slip until it burns through from friction.

Hoover Vacuums | Answered on Nov 20, 2017 | 36 views


hi helen.
that does not sound good.
you might have to open it up and have a look inside and see if anything has burned out.
or get some one to look at it for you.

Hoover Vacuums | Answered on Nov 17, 2017 | 29 views


Counter clockwise

Hoover Floormate... | Answered on Nov 16, 2017 | 55 views


Thermal fuse failed, motor brush gear stuck, switch failed, power cord...

You will need to dismantle it and check the circuit with a meter...

Hoover Vacuums | Answered on Nov 15, 2017 | 34 views


There is a duct in the front of the water recovery tank that you remove to install the upholstery hose. If this duct is missing or not installed properly you will have no suction

Hoover SteamVac... | Answered on Nov 13, 2017 | 226 views


Check the opening behind the floor brush for obstructions there.

Hoover U5018-900... | Answered on Nov 09, 2017 | 50 views


-What about...? It a not bad brand.

Good luck and clean a lot

Mai

Hoover Vacuums | Answered on Nov 07, 2017 | 30 views

Not finding what you are looking for?
Hoover Logo

Ask a Question

Usually answered in minutes!

Top Hoover Vacuums Experts

Les Dickinson
Les Dickinson

Level 3 Expert

18408 Answers

Gerry Harvey
Gerry Harvey

Level 3 Expert

1467 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17130 Answers

Are you a Hoover Vacuum Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...